Shopping Cart

Your cart is empty.

Your cart is empty.

Feekoon 4 Pack SS2 Float Switch L Shape, AC Float Switch with 3/4 Inch Adaptor and 6Ft Wire, Water Float Switch for HVAC System with Condensate Overflow Detection

5.0 (8) Write Review
Free shipping on orders over $29.99

$45.99

$ 20 .99 $20.99

In Stock
  • HVAC Float Switch Function: SS2 water level switch is applied in HVAC systems to detect condensation water overflow; It detects blockage of air conditioning condensate water drain pipe and shuts down the system to prevent overflowing water from damaging floors, walls, and ceilings
  • Working Principle: the float switch HVAC can be connected to a VCC or thermostat line; It is an NC type (normally closed) switch: when no water overflows, the float stays at the bottom of the switch, the switch closes the loop and outputs an ON signal; When the water overflows, the buoyancy of the float rises, the trigger switch turns on, and the output OFF signal turns off
  • Specifications: switch type NC (normally closed), material PVC, operating temperature -20 - +80℃, wire length 5.8ft, switching voltage max; 200VDC; Switching current max; 1 A contact rating maximum 10W
  • Easy to Install: this float switch HVAC is easy to install, all you need to do is install the 3/ 4 adapter that comes with the AC float switch on the auxiliary drain outlet of the main panel and connect the 5.8ft of wire to VCC or thermostat wire
  • Easy to Clean: the transparent material allows you to see what's going on inside; The float switch is equipped with a removable cover; When you use it for some time, you can remove it for cleaning to ensure hygiene and normal function



Are you still worried about soaking your furniture due to condensation leaks when using your HVAC?

Then you absolutely need a float switch! Here are the specific installation steps for you:

INLINE INSTALLATION FOR (WALL) UNITS WITH VERTICAL DRAIN OUTLETS
It is recommended that this device be installed on the primary drain line between the pan outlet and P trap on wall units with vertical drain outlets. This will prevent the switch from shutting off the fan coil or activating the alarm circuit in the event condensate drips directly from the coil into the auxiliary pan outlet when the coil becomes dirty.
1. Disconnect power to unit at main panel and glue 5'' stub down from the primary pan outlet.
2. Glue 3/4'' Tee to bottom of stub with Tee stem horizontal and plumb.
3. Glue 3/4'' stub into horizontal outlet of Tee, insuring it is also plumb.
4. Ensure switch/plug assembly is inserted into 1'' inlet of PVC elbow so that float stem is at inside (bottom) of switch elbow. Float stem can be adjusted by threading it out of the plug assembly. DO NOT GLUE.
5. Glue a drain line with P trap onto the remaining outlet of Tee.
6. Connect the wires to VCC or the thermostat wires.
7. Test switch by lifting float with unit running. Unit should stop running if correctly connected.
8. Test all fittings and connections for plumbing leaks.

INSTALLATION FOR HORIZONTAL CEILING (PANCAKE) UNITS
NOTE: Primary drain (inline) is also recommended on horizontal ceiling (pancake) units as some flooding may occur if installed on auxiliary outlets, due to the closeness of the outlets to the top of the pan.
1. Glue 3/4'' stub to primary pan outlet.
2. Glue 3/4'' Tee onto stub with Tee stem positioned horizontally away from the unit and plumb.
3. Follow steps 3-9 under INLINE INSTALLATION FOR WALL UNITS, above.


Charlie
Reviewed in the United States on January 13, 2025
Than waiting until the water hits the floor and then trips a sensor.
Seth G.
Reviewed in the United States on September 13, 2024
Great idea so far so good
michael h.
Reviewed in the United States on September 10, 2024
Need a male attachment this was female. Sadly was my error not returning sooner.My significant partner died and too much more important things to consider
Customer
Reviewed in the United States on August 26, 2024
Nice that it's see thru
Barbara Buckley
Reviewed in the United States on July 9, 2024
Great that you can see what is happening with the float before there's a problem. Very easy to install and works better than the original.
Dan W.
Reviewed in the United States on December 21, 2024
Nice switches...I like that they are transparent!
Leonard S
Reviewed in the United States on November 10, 2024
Easy to put in
eric
Reviewed in the United States on October 16, 2024
Should’ve went With Rector seal version like I’ve used in the past. I thought these would be nice cause you could see in there to see that there is water buildup, but the threads are straight threads not tapered NPT threads and the slip pipe fittings are not standard. So I couldn’t use it with my own PVC to thread adapter.