Your cart is empty.
Your cart is empty.Product Description
Features:
The heavy-duty snap ring pliers set heat treated steel circlip inch pliers for large equipment repair and replaceable tips and spring ratchet locking mechanism to securely hold against snap ring tension.
Each pliers has an overall length of 16 inches and a handle length of 12-1.2 inches.
The internal pliers’ capacity is 3-1/16 inch to 6-1/4 inch (78 mm to 159 mm) snap rings and the external pliers’ capacity is 3-1/2 inch to 6-1/2 inch (89 mm to 165 mm) snap rings.
3 Sets of Different Angles
Quick-Change Snap Ring Tips
2x straight tip, each 0.12 inch (3 mm)
2x tips, each 0.12 inch (3 mm) 45 Degree
2x tips, 0.12 inch (3 mm) 90 Degree, tip retaining screws
Package includes:
1x Internal snap ring pliers,
1x External snap ring pliers,
2x straight tip, each 0.12 inch (3 mm)
2x tips, each 0.12 inch (3 mm) 45 Degree
2x tips, 0.12 inch (3 mm) 90 Degree, tip retaining screws
With a blow-molded for storage case.
Johnnie Danger
Reviewed in the United States on September 16, 2024
Got this tool for one specific purpose, the giant snap ring on holset turbos for when I need to clock it. Used the 90° tips and all the way open was just enough to grab it
Len K.
Reviewed in Canada on August 26, 2024
I am disassembling an 1987 OMC Cobra stern drive lower gear housing to install an updated detent and needed the HD snap pliers to remove two heavy duty snap rings, so I purchased these two. The holding bar was a little to big to allow to reach the two snap rings deep in the propeller shaft, so I removed it and compressed the rings with the blue holding device. I had those two heavy duty snap rings out within a couple of minutes. Couldn't be happier. Because each holding bar is the same, I will cut one down to fit inside the shaft and move the holders from pliers to pliers if needed.
Robert Culbertson
Reviewed in the United States on October 20, 2024
This tool will make your life easier when dealing with heavy duty snap rings.
Rosario Duran Jr
Reviewed in the United States on March 5, 2023
They dont feel extremely cheap. Actually somewhat tough. Help to install and remove 6r140 case snap rings. Probably help with the 6r80 snap rings too.
Customer
Reviewed in the United States on October 22, 2023
Needed a large pliers kit to work on automotive transmission. Worked well. Not SnapOn but does the job and after multiple uses, no perceived wear on tips. For the price, recommended.
Wesley
Reviewed in the United States on January 20, 2023
This was a good buy. The locking mechanism is the important part. Removing large snap rings without an extra hand can be cumbersome. The locking feature fixes that problem by allowing you to remove a hand and pry the remaining portion of the snapring out of the groove. Same type of car, same job, new tool and it probably save me 30mins and some frustration. Quality is a little sloppy but it was nothing 5 minutes and a file couldnt fix.
Customer
Reviewed in the United States on June 11, 2022
Works as it should good value for the money
Laif Matsuk
Reviewed in the United States on October 1, 2022
I really only got these to do one job that required a large set of snap ring pliers. They worked well enough for that job but I would recommend getting something a bit nicer if you foresee yourself using these more than a handful of times.The build quality is okay but not great. I noticed a small bend in the tips after the first 2 uses, nothing major but enough that I can only see getting a dozen or so uses out of these before needing a new set of tips.The ratcheting mechanism feels rather cheap and I never found it very useful to be perfectly honest. It seems to work okay however given the option I would have rather just not had it to begin with
Jon B. Snyder
Reviewed in the United States on January 22, 2020
Working on an Evinrude 115hp motor gearbox with some serious circlips, deep within the torpedo. No prayer of getting my standard snap ring pliers to work in this situation, predominately because they are too short to allow the jaws to expand enough to engage the retaining ring, but in retrospect after using these pliers - mine would have never had enough beef for the task. These worked flawlessly, a little difficult to get in place due to the depth of the ring, diameter of the torpedo, and presence of the prop shaft - but once on, they locked on and made a problematic task easy. The "real McCoy" pliers from the OB manufacturer are $125.00 and can't possible perform any better! Thanks!
Recommended Products