Shopping Cart

Your cart is empty.

Your cart is empty.

SSR-80DD Solid State Relay DC to DC (Input 3-32V DC Output 5-60V DC) with Heat Sink, 80A

4.8 (3) Write Review
Free shipping on orders over $29.99

$14.90

$ 6 .99 $6.99

In Stock
  • Model: SSR-80DD, single phase Solid State Relay 80A DC to DC control, CE Compliant to EN60950-1
  • Input voltage 3-32V DC, Load voltage 5-60V DC, Max load current 80 Amp
  • Rugged epoxy encapsulation construction, high isolation over than 50MΩ(500VDC), high dielectric over than 2.5KV, output snubber circuit protection
  • No EMI/EFI & Low surge by Zero Cross Trigger method, specially suited to control sensitive, capacitive and Non-saturated inductive loads
  • SSR switches use semiconductor component acts as a switch for the relay, no moving parts inside, no mechanical wear, no action noise, no mechanical failure, and high reliability


DMWD Low cost single phase solid state relay SSR-80DD

Input voltage 3-32V DC

Load voltage 5-60V DC

Load current 80Amp


80A 3-32V DC to DC solid state relay (SSR) features high structural strength, good impact resistance, and strong shock resistance. The SSR offers a reliable switching the commercial and industrial loads, such as computer peripheral interface device, printing machine, molding machine, food machine, packaging machine, and so on.


  • Built in RC absorption
  • Photoelectric isolation
  • SCR output
  • LED indicator for operation status
  • Panel mount
  • Zero-crossing switch type
  • UL Approved, CE Compliant to EN60950-1


Note:

* When the load current is higher than 10A, a heat sink must be installed to the solid state relay, or the SSR relay should be mounted on a metal base plate with heat dissipation effect, and the thermal grease is applied between them.

* When the load current is 40A or more, a fan cooling radiator or water cooling radiator must be equipped.

* Heat sink is included.


Package Content:

1 x Solid State Relay

1 x All Aluminium Heat Sink


Size/Weight:

SSR(60x45x23mm/100g)

Heat Sink(78*50*50mm/80g)


Warranty:

Free new replacement in 5 years, Have faith in quality


Surendra Prajapat
Reviewed in the United States on June 4, 2024
Works great without heating up. I had tried similar product in the past and even at 24/1amp they will heat up a lot. This one does not, good quality.
anonymous
Reviewed in the United States on May 9, 2024
I know that a lot of inexpensive SSRs are rated above their capacity, so I made sure to oversize to my needs and get one with a heatsink. I am running 50-54VDC AT 16A through this SSR rated for 60VDC at 80A and it gets blisteringly hot within moments. I even tried putting a cooling fan but it still is way too hot for me to be comfortable using it. I switched it out for a 30A SSR from a well-known industrial automation company and it handles the 16A while barely getting warm to the touch.
Customer
Reviewed in the United States on November 10, 2023
Quick answer avoid, pick a different brand.On my 3D printer I needed to replace the Solid State Relay that controls the hot-bed. I selected this brand as a close match for the original (different brand but with the exception of the sticker it looks identical). The original was a 40 amp so I replaced with a 40 amp, original was not on a heat-sink so I reinstalled identical to the orig. The replacement died within 1 hour of installation. Replaced it with 80A and a 40A fuse... same problem, Replaced again, with provided huge heat-sink, replaced the load (hot bed), 3 down. Replaced it with different brand, works fine, does not need the heat-sink. Glad they were inexpensive... this was an time-consuming problem. If you are switching any current at all pick a different brand.