Your cart is empty.
Your cart is empty.Product Description
1/4" (Dia.) Bevel Trim Bit with 1/4" Shank
From the Manufacturer
Freud's solid carbide bevel trim bit trims and produces a 7 degree bevel to give a finished look to plastic laminates. The self piloting feature eliminates the expense and upkeep of a ball bearing assembly. Covered by Freud's limited lifetime warranty.
Deborah S Wallace
Reviewed in the United States on February 28, 2023
Only used for countertop laminate... excellent performance
MissississississippiMan
Reviewed in the United States on December 28, 2023
Worked great for my first laminate countertop install. Used it to trim of countertop-top to front edge. Bit of coconut oil for lube smeared on the laminate and didn't have any trouble with marring at all. Do recommend for sure getting the depth dialed in on a scrap piece though. Too deep and it will skim the face of the edge, too little and it will leave a lip.
Me Myself and Mwa
Reviewed in the United States on January 11, 2022
I did my entire kitchen with this bevel bit without any problem and its still got alot of miles on it. Good bit for the cost, id buy it again , and i will if this one weary out.
guillermo armando garcia picos
Reviewed in Mexico on February 22, 2019
excelente accesorio para cortar los cantos de formica muy util para mis trabajos de carpinteria recomendado al 100%
Ian Surahim
Reviewed in the United States on October 22, 2019
Seriously does what it was made to do. No more messy filing with laminate files and sandpapers. Awesome bit to have in your arsenal.
Cliente de
Reviewed in Mexico on October 16, 2019
se debe poner una protección en el material que tiene acabado para que no se dañe, como cinta maskin u otro. pero el funcionamiento del producto es muy bueno. corta muy bien.
Clara Germiller
Reviewed in the United States on September 20, 2018
This worked perfectly for my laminate countertop. I literally tried everything to trim the corners and nothing worked until I found this! I'm so happy
Andrew W
Reviewed in the United States on August 13, 2018
I used this to trim the top laminate surface of a new countertop. I used a "standard" 3-flute carbide cutter with bearing for trimming the front face, and sides because I did not want the edges to have the 7° cut that this cutter makes. For trimming the top though, this worked great in 1 pass, moving pretty quickly. As others have mentioned, you probably do NOT want to move too slow, otherwise you might burn the work where this rubs against the other face. Some people apply soap to help, but I did not see any issue.
asdfasdfasdf
Reviewed in the United States on June 21, 2018
I used this bit to trim some laminate today and it worked quite well. I like the fact that there is no bearing. One reviewer pointed out that the "bearing" surface has potential to mar the laminate. I first applied and trimmed the side pieces, then applied the top laminate. Before trimming the top I rubbed some Gulf Wax on the sides to act as a lubricant/protectant and got no marring. Would buy this bit again.
Customer
Reviewed in Canada on November 9, 2018
I bought this product to test it out on laminate edges. I’ve done a lot of filing and wanted to eliminate most because of the repetition and how it’s affecting my shoulder. This product is the problem solver. I use a flush trim bit with a smaller bearing to remove the bulk of material. I then follow it up with his product set at just the right depth to chamfer the edges and leave a beautiful, smooth edge that requires zero filing.
Chan K.
Reviewed in Canada on June 25, 2017
no CON here. it does what it suppose to do :)it's cheaper then local store (home depot, reno depot, rona,etc)
Corey
Reviewed in Canada on April 7, 2017
Great product
M. Otto
Reviewed in the United States on April 25, 2015
Works well enough, but the "bearing" end of the bit can mar laminate if it's 90 degrees to the surface you want to trim.
Recommended Products
