Your cart is empty.
Your cart is empty.Product Description
Diamond Core Drill Bit BRSCHNITT (Triangle Shank,5/8-11 thread,Hex shank)
1
2
3
Hand Drill / Bench Drill /2000-6000RPM
Machine
1.Machine
Widely used Hand Drill, Bench Drill.
Attention:Angle Grinder.When use Angle Grinder,please install angle grinder drill chuck
2.When using, Recommended speed 2000-6000RPM, the faster the better
Operation Step
Step1
Place the drill at a 45 degree angle
Step2
Drilling till the hole start to form
Step3
Bring the drill up into upright position
Step4
Continue to drill and swaying the machine along a circle
Gabriele
Reviewed in Italy on January 15, 2025
Ho acquistato queste punte diamantate per il trapano e, nonostante il prezzo economico, funzionano sorprendentemente bene. Si comportano come ci si aspetta, tagliando in modo preciso e senza problemi su superfici dure come ceramica e piastrelle. La qualità è buona per il costo e, sebbene non siano di livello professionale, sono perfette per l'uso domestico o per piccoli lavori fai-da-te.Un acquisto consigliato a chi cerca punte funzionali e a un buon prezzo.
Della
Reviewed in the United States on September 22, 2024
I used this bit to drill holes for my flower pots. Some were a good half inch thick and others were less than a 1/4 inch. I had no problem getting a nice clean hole. I have bought other bits in the past that didnt work as good as these. I will buy these again.
Jeff Stearns
Reviewed in the United States on September 16, 2024
These are a great value. I bought a package of 5 for less than $20.I was curious about how well they'd perform, so I did a side-by side comparison between the 6mm bit and a brand new Big Name Brand 6mm diamond bit. I paid approximately the same price for one Big Name Brand drill bit as I did for the package of 5.I needed to drill 12 holes in porcelain tile. I drilled half of the holes with a BRSCHNITT bit, and half with the Big Name Brand bit. I kept the work area wet and maintained steady pressure at 2500 RPM. Interestingly, the BRSCHNITT bit was slightly faster at first, but both bits performed about the same overall. I couldn't really detect and meaningful difference between them.So my conclusion is that these bits are a perfectly acceptable alternative to the Big Name Brand bits that cost about 5 times as much.
Elizabeth A Scott
Reviewed in the United States on July 10, 2024
The bits are well made and lasted much longer than other bits of the same size.
Salvatore
Reviewed in the United States on May 10, 2024
I needed to cut hole in granite counter top to install RO water spigot. This thing worked way beyond my expectations. Used a little water from sponge, no dust just a little "mud" that I wiped away as it built up. The only draw back is the core got stuck in the bit and no side holes on the bit to facilitate removal. So I used the second bit to finish the job.
George T.
Reviewed in Canada on February 6, 2024
Does what it should do. Used for tile
ns
Reviewed in the United States on December 8, 2024
These cut porcelain tile very well, but unfortunately the design of the bit means that a ceramic plug is left lodged inside it.There are no slots on the side to push the plug out. So the bit is useless the second time you try to use it. That’s a shame because I was otherwise happy with how it cut through porcelain tiles.
Daniel R.
Reviewed in the United States on December 15, 2024
these bits cored through extra hard concrete that my hammer drill could not penetrate. they come pre-loaded with a cooling/lubricant wax on the inside of the cylinder. Even after this job they seem to have plenty of grit left leaving them in good shape for the next one. happy customer especially for the price, thanks
Dave
Reviewed in the United States on November 21, 2024
I've seen big holes knocked out of conc. blocks by people trying to make a hole for water pipes or spigots. This drill is perfect for making a small hole for 1/2" pipe. Be careful that your bit doesn't fall into the block. Sometimes the magnet isn't powerful enough to hold it when pulling it out. I'm looking for ones for a 3/4" hole???
jose velasco
Reviewed in the United States on April 22, 2024
Just go slow on your speed and spray water
John45170
Reviewed in France on July 18, 2023
Forêts mèche diamant 6mm pour porcelaine carrelage. Bonne qualité un lot de 3 .Conforme
MAJI sas
Reviewed in France on July 15, 2023
Je viens d'essayer un forêt dans une pierre relativement dure. Le perçage sans percussion a été réalisé sans trop d'effort.Je recommande ces forets dont le prix est abordable.
Anders Haby
Reviewed in Sweden on January 8, 2023
I've only drilled two holes in porcelain so far but I have no complains. Made some really nice holes
Recommended Products