Your cart is empty.
Your cart is empty.Product Description
Reneau Frigon
Reviewed in Canada on February 25, 2025
Great to apply sticker to car without bubble.
Jim Jones
Reviewed in the United States on August 31, 2024
This stuff is great (yeah I was skeptical at 1st). I've used the soap trick on previous applications but was having a problem with a 3M vinyl application over a curving fender. After two failed attempts I order this stuff and smooth as glass it's on...and easy!
Canadian Gypsy
Reviewed in the United States on August 28, 2024
Works exactly as described ... didn't have much issues with this product ... the wrap I used seemed to work well enough as well ... for LARGE area's ... ie) a car's hood - or - any majour sized area - take your time working with both this product & the vinyl your trying to put down & you'll be fine ...
Al
Reviewed in Canada on July 18, 2024
The best product to use for applying striping to a vehicle. Easy to use and works perfectly to keep the striping movable until perfectly placed. The squeegees and towel included are handy.
SB
Reviewed in the United States on May 26, 2024
Product worked wonders for wet application of vinyl racing stripes! So easy!
Stud E Baker
Reviewed in the United States on May 22, 2024
I install the door decals on the trucks at my work. This stuff works very well. You have a minute or two before you can't slide it around comfortably anymore, but if your prep is good and measured out, it works well. Easy clean up. Squeegee works well. On the thin side, but that makes it more manageable.
Chase W.
Reviewed in the United States on May 18, 2024
Worked better than a soap/water solution that I normally use to apply graphics. Faster dry time but not so fast you can’t work with it. Prep is easier since it doubles as a cleaner too
Nick Bennett
Reviewed in the United States on November 2, 2024
This helped me add the side & quarter glass decales to my car, along with a hood decale & there is still 1/2 a bottle left.
Dallas S. Scholes
Reviewed in the United States on April 3, 2024
The product works well, easily removes the excess material from the old decals and makes application a breeze. Instructions are easy to follow on the bottle and makes removing air bubbles a breeze ensuring a easy application.
Customer
Reviewed in Canada on December 13, 2023
This makes applying vinyl or laminate so easy. No bubbles , lots of time to get vinyl in place. So easy to use
Richard C
Reviewed in the United States on August 6, 2022
It's too expensive for cleanig. 50/50 of Distilled Water, to 91% Alcohol is Better. 30% D.H2O, to 71% Alc. for cleaning. Now using it as an applicator is Awesome. But remember on thing, you have approximately 90 sec. Example a 03 Silverado Hood, full Carbon Fiber vinyl 🙄, after positioning vinyl, spray liberal amounts on hood, then tack 1 side, peel backing back, and spray the adhesive side as you peel. I recommend 2 people, I did it alone. This Rapid Tack, i highly recommend, but once it sticks, it's hell, picking it back up, to either get to some fingering, and or Bubbles. Respray gingerly when repositioning. The more you spray and repositioning, the harder the job, and compromising the overall results.I Strongly Recommend you watch a YouTube video or 2 about this product. Due only half the Hood first, then start in middle, and squeegee from top to bottom being sure your vinyl is in the position, and hasn't moved. After installation is complete, make sure you heat up the Vinyl from center out, to activate the adhesive on the vinyl, and check for bubbling. Approximately around 100°, about 4" from surface, with a sweeping motion. Rapid Tack to me, speeds things along quicker and easier, especially with experience. Try a small piece piece of scrap vinyl, on vehicle to see how it works. Remember to clean thoroughly w/distilled or purified water, to 50% alc. Wipe any smear marks off. 👍😎✌👍😎✌
Recommended Products