Your cart is empty.
Your cart is empty.Product Description
Advanced production equipment
Fully automated coatinge quipment
Each coating tool use the world's most advanced PLATIT(Switzerland) coating technology, ensure the cutter hardness and life can be increased by more than 2 times in the cutting use.
Defect quality control
Using advanced testing equipment Walter tool measuring instrument, to achieve all testing products.Ensure each tool to achieve defect quality control, make cutting tools ahead of peers.
Fine cutting edge passivation technique
Use the European advanced cuttingedge passivation technology, greatlyimproves the tool life and the machining efficiency, reducing the roughness of the workpiece.
HIGH HARDTUNGSTEN STEEL
lt belongs to universal tungsten steel tool
HIGH EFFICIENCY MACHININGFROM ORDINARY STEELTO PRE HARDENED STEEI
HIGH HARDTUNGSTEN STEEL
It is widely used, The cutting process is fast
4-Shank diameter
HRC45
Coating hardness 3600HV
Processing form
·Side machining
·Surface machining
Processing form
·Straight flute machining
·Deep groove processing
END MILLS SPEED REFERENCE
1、The above table is the standard value of side milling processing, when the tool cuts the groove, the speed should be 50%~70% of the above table,and the feed rate should be 40%~60% as the standard value.
2、Please use high precision machine tool and tool shank 2.
3、Please use air cooling or cutting fluid which is not easy to produce smoke.
4、Side milling is recommended for smooth milling process.
5、 lf the machine tool and the workpiece are installed with poor steel, vibration and abnormal sound will be generated, then the speed and feed rate of the above table should be reduced year-on-year.
6、In the condition of non-interference as far as possible to make the tool overhang the shortest lengthTranslated with DeepL/Translator
SCOPE OF APPLICATION
ALLOY STEEL
CARBON STEEL
PRE-HARDENED STEEL
CAST IRON
1
The unique tool structure and reasonable groove design result in excellent cutting performance.
2
Negative rake angle design enhances the rigidity of the tool,and the large core diameter is more stable.
3
Pilates coating,The special surfacepost-treatment can effectively reduce the friction,make the chip evacuation more smooth,and the surface quality is better.
Advanced production equipment
Johnny V
Reviewed in the United States on January 29, 2025
As the headline states: Nice Quality - Sharp End MillsI'm just starting my journey with a home CNC machine and gathering bits and mills to get up and running. I have not cut with these yet but the quality is very high and the edge sharpness is flawless. The price is amazing for the quality.
Amish Country
Reviewed in the United States on September 9, 2024
Product Reviewed: Micrograin Carbide End Mill - 4 Flute-6mm Shank 6mm Diameter. (5 Pieces) for $28TL;DR; Fine Grind; Good Mfg PackagingI use these end mills in a home shop environment. I didn’t try a cut with this one but broke out the macro lens so you can see the edge quality.5 Stars Very Good valueHow I review:Reviews start with 5 stars and I subtract points.- 0 for value but I try to provide guidance-0.5 to -3 for product not matching description e.g. stainless steel is actually plated steel-0.5 to -3 for product missing badly on executionI select products carefully so low (1-3 scores) are rare but detailed comments and critiques almost always are in the review. Most of my reviews come out 4-5 range.If possible I dismantle or destroy items to examine inner workings.
TM Carr
Reviewed in the United States on September 29, 2024
Good quality, sharp end mill. Works great and leaves a nice clean finish.
JP
Reviewed in the United States on September 13, 2024
The initial inspection was positive - well machined, sharp, relief cuts on tip to allow plunge cuts, and coated for steel machining - Not for aluminum. After putting one in the collet, I measured runout at .0003", well withing normal tolerance. I cut some mild steel and it did well, cutting cleanly at normal feed rates. I slowed the feed way down and tested on some RC50 bar stock. It cut clean, but after cutting I found one chipped tip. I have cut this material before with other carbide tooling without tool damage. Given the results, I would use these mainly on mild or softer steels to save wear on my expensive cutters so I can use them on harder materials. I rated these based on cost/performance. They are good cutters for the price, but they do have limitations.
Customer
Reviewed in the United States on August 8, 2024
This review is for Micrograin Carbide End Mill - 4 Flute-6mm Shank 6mm Diameter. (5 Pieces) AlCrXN Coating End Mill Bits CNC Milling Bit Apply Milling Alloy Steels, PRE-Hardened SteelThese mills are very well finished, with no observable defects under 40x magnification.Using my Taig CNC mill, I was able to slot 304 stainless steel bar stock and also some hot rolled plate with good results. I used a small amount of cutting oil and a light depth of cut, but the finish was quite good. I noticed that 2 of the flutes join at the center, so plunge cutting should be possible with very slow vertical feed rates. The manufacturer says that edge cuts and light slot cutting are the recommended uses. There was no discernible wear nor any chipping of the cutting surfaces, even after running 150" of cuts.These mills should not be used on aluminum stock due to the coating.These fit well in a ER16 1//4" collet.I really like these end mills, which provide a very nice finish when used properly. I only wish that they would provide chip loading and recommended feeds/speeds as part of their listing.At this price, this is a good deal for ferrous metal machining. Recommended.
Buk Lao
Reviewed in the United States on October 4, 2024
These end mills (6mm) work great for me. I don't have them in a CNC machine but instead I use them in my drill press. Like anything done this way, your workpiece really needs to be held well but assuming that is done correctly, these end mills will go through anything that I've thrown at them. Brass, aluminum and mild steel are all very easy to work with these end mills, which are very sharp. The price is affordable and you should consider purchasing them. I would recommend these to anyone who needs end mills for whatever milling you do.
Gear Report
Reviewed in the United States on October 23, 2024
I got these for my personal desktop CNC machine. They do well form my aluminum cutting projects.
medjohnson
Reviewed in the United States on October 11, 2024
So far so good, and it is cutting well. Will update on any issues or bit life that come up.
Recommended Products
$75.99
$ 34 .99 $34.99