Your cart is empty.
Your cart is empty.Product Description
The fits Mansfield 210 and 211 valve seal is designed to fit both 2 inch 210 and 211 Mansfield flush valves. Easy to install, the 427 includes: (1) valve seal.
From the Manufacturer
Over fifty years ago, Lavelle Industries launched the first toilet flapper, the Original Korky. Since then, plumbing contractors and home improvement retailers have relied on the Korky brand for innovative products and outstanding service. Korky toilet repair products include a complete line of flappers, fill valves and flush valves. Lavelle also manufactures plumbing specialties such as toilet plungers, seals and washers.
John
Reviewed in the United States on March 12, 2025
Worked great on my old mansfield
M. B.
Reviewed in the United States on September 6, 2024
Easy fix but be advised that the toilet might run for a bit after installation. After a day or two, the seal sort of relaxed and molded itself to form a watertight seal.
SteveH@Indy
Reviewed in the United States on July 8, 2024
Easy replacement to stop slow leak to bowl because of cracked original gasket on flush valve assembly. Check to see if it is just dirty due to hard water first. If cracked or torn, this works great. I keep one on hand always as a spare. These are also readily available at local stores at similar prices.
Shasha
Reviewed in the United States on June 30, 2024
After watching some YouTube videos wondering what the cause of my toilet randomly running every 20 minutes, I decided to purchase this to give it a try. It was so easy to install and it worked! This product was less that $3, cheaper than Home Depot and ace hardware. It really works!
shallot
Reviewed in the United States on December 4, 2024
The problem with these seals is they work fine for about a year but then the water deteriorates the seal and you have to replace them annually. Bad rubber or whatever I don't know
Hussein Hernandez
Reviewed in the United States on April 19, 2024
Toilet kept running, I kept putting it off, I finally got around to looking up the model number of the toilet, it's at least 20 years old. Looked to see what the issue was, where the leak was coming from, and this seal was the culprit. I looked up some youtube videos to make sure I was going to do it correctly. I looked up the model number on Amazon, and "Viola". Best price in town and next day delivery cant beat that. Have had it for a while, super easy to install. Absolutely recommend.
Loves Stuff
Reviewed in the United States on April 24, 2023
This will fix your toilet if it is either hard to push the flush handle, OR, if it keeps losing water from the tank and keeps running a few seconds to refill the tank that is leaking water into the bowl. I was confused by the description that it fits all 210 and 211 because I thought that was the toilet number, and mine is Mansfield 140. The 210/211 is the part number of the flush assembly that goes up and down. Mine actually has the water saver version in it, which doesn't matter, as this matches the size of the flush hole in the bottom of the tank. First look at the top of the flush device and see a flat round piece on top where the overflow tube goes in. Remove the tube and unscrew the round disk counter clockwise. Without that, the tall flush device will lift out, and you will see the old red washer at the bottom. When it is going bad, it will swell and make it hard to push the flush lever. When it is ruined it will start letting the water leak out of the tank and you will hear the water run a few seconds again to refil what the tank lost. Remove that old seal and put the new one in. There are usually 2 ridges and you want the red seal to be between those ridges. So work it around until it is under the top ridge and now it is between the two of them. Should there only be 1 ridge, work the red seal over it and make sure it is up against the bottom of that ridge. Clean off the edge of the "up and down" flush piece, so there is no sediment to keep it from sealing completely, and place it back in the tank, on top of the new flat red seal. Screw the top disk back on, put the overflow tube back in, and test flush before putting the lid back on, waiting to make sure you hear no water come back on in the tank. I have suffered with a mal-functioning toilet for a long time, and it was done if 5 minutes! If you have any doubts, there are many videos on youtube, just search Mansfield toilet running.
Les Robinson
Reviewed in Canada on December 4, 2021
washer did the trick.
Liz Wick
Reviewed in the United States on June 3, 2016
I am unfortunate enough to live in a home with 4 Mansfield toilets. If you have any experience with their flush valves, then you know you will need to keep a backup supply of new valves on hand. I've been in the house for 5 years and every toilet in the house has to have the valve replaced about once every 6 months. I kept buying the replacements from the local hardware store and they are a pain to install, they would never seem to seat correctly, and they just start to disintegrate after a short period of time.The last time I ordered these rather than the hardware store replacements and noticed a difference right away. The rubber is wider and they have a tighter fit, which means that they were easier to install as it was obvious if they were seated correctly and the wider rubber forms a tighter seal with the flush mechanism. It's only been a few months so I can't speak for how long they last, but so far they are much better than the other replacements.
Recommended Products
$21.00
$ 10 .99 $10.99