Your cart is empty.
Your cart is empty.Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane intake manifold is optimized to deliver superior performance with Edelbrock square-bore Performer Series or Thunder Series AVS carburetors. This small-block Chevy manifold has a runner design that's "tuned" for peak torque at 3500 rpm on a 350-inch engine and it's ideal for power from off-idle to 5500 rpm. Dyno tests showed gains of 5 HP and 9 ft-lbs. of torque over the Edelbrock Performer manifold #2101 on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft-lbs. of torque for more performance where you need it most. Performer EPS manifold #2703 combines a modern runner design with a front mounted oil fill tube for those who want the vintage look of our Classic valve covers with no breathers. #2703 has the same performance features as the Performer EPS #2701. Includes Oil Fill Tube (not installed) and matching push-in breather cap. The Oil Fill Tube and Breather are also available separately as #4803. Match with a dependable Edelbrock square-bore carburetor for maximum performance gains. Also available with choice of four finishes. Will not fit under stock Corvette hood. ** Carburetor Recommendations: Edelbrock Thunder Series AVS or Performer Series carb, 500-650 cfm. Installation Notes: Recommended intake gasket: Edelbrock #7201. Manifold ht: A-3. 74", B-4. 80"; Carb pad height: 4. 27". Port exit dimensions: 1. 15" x 1. 87". Camshaft Recommendations: #2102, #2103, #2208, #2209
Ralph Wieman
Reviewed in the United States on April 25, 2023
awesome
Fedman
Reviewed in the United States on May 31, 2022
this engine has never run this good
RV
Reviewed in the United States on April 26, 2022
Had to grind a little for the cylinder head cover to fit properly...
Rich
Reviewed in the United States on June 21, 2020
Needed an intake with an oil fill tube for an old Corvette. May be important for some to know, this will fit under the stock hood with a Holley carburetor and a drop base air cleaner with a 2" element. FYI the fill tube is on the opposite side of the stock intake, and I used a different thermostat housing.
rosie
Reviewed in Canada on April 2, 2020
Amazon ship newer model picture showed older model
Ranger Rick
Reviewed in the United States on June 2, 2017
Good street performance manifold at a reasonable price. I bought this part number because it has the old SBC oil filler tube on the front, which is similar to the original that was on the 1962 327 I was rebuilding. My oonly disappointment has been the breather cap on the end of the tube. I have been through 2 of the Edelbrock breathers, and they keep coming off going down the road due to poor design on the spring clip inside. It is loosely riveted, lacks enough pressure, and is bent with little actual contact surface. When compared to my old AC Delco original, it appears cheaply made. I am currently using the old, faded black original which looks ugly on a fresh motor until I can find a suitable replacement. I have contacted Edelbrock customer service, but they don't have an answer or better replacement. If you buy this manifold, go into it knowing that you need to buy a different breather right from the get go.
d*****1
Reviewed in the United States on September 20, 2016
fit good,looks good.didn't use the filler neck that came with it because i needed the one with the pvc valve provision. but the one that comes with the manifold doesn't fit very well.just a heads up on that.
BIG ECE
Reviewed in the United States on May 24, 2014
As ordered on time. All parts accounted for. Outstanding engineering direct fit on 350 small block. Quality and accuracy received.
Souci
Reviewed in the United States on March 14, 2014
Quality parts at a better price than I have found elsewhere..Part fits and looks great have not tested the part on my car yet ... the engine is still on the stand.
Recommended Products
$23.99
$ 9 .99 $9.99