Your cart is empty.
Your cart is empty.Niagara Cutter uses an "extra fine" grain cemented carbide raw material that is a true sub-micron grain tungsten carbide alloy. Niagara Cutter's carbide material is classified within the C1 to C4 range, and has an excellent combination of strength and toughness. Using raw materials with unique properties and high purity ensure Niagara Cutter's consistent high quality. Specifically designed for machining Aluminum, Stainless Steel, Titanium and Exotic Alloy Materials. Niagara Cutter is a leader in cutting tool technology and is proud to have their products made in the USA.
Steven Gould
Reviewed in the United States on January 27, 2024
Started to work but it got to hot without cutting oil and broke.
rmartine
Reviewed in Mexico on May 9, 2023
Me funcionó muy bien en el torno y en la fresadora casi no se ha gastado la recomiendo ampliamente y el precio me parece muy justo
Cody W Colvin
Reviewed in the United States on October 4, 2023
Good quality end mill. I only needed this for cutting one slot so I haven't put its durability to the test, but it seems well made and gave a nice surface finish. Wouldn't hesitate to buy more Niagara brand tools.
David A.
Reviewed in Mexico on September 19, 2022
No lo devolví solo porque me urgía
famof5
Reviewed in the United States on March 17, 2021
I like the cuts it made before it broke, which gives it 1 star. It broke after only a couple uses. I was making shallow cuts in birch wood at average speeds on my CNC. Bit broke in 2 places on the shaft. I don't see any information about a warranty. If seller decides to replace I would adjust my review.
D. Afyd See
Reviewed in the United States on October 12, 2019
I like this bit. I use it in my Shaper Origin CNC router. Seems to work better than the ones from the router manufacturer (and less expensive). I am planning on getting another so that I'll have a spare. I don't really know about durability yet. Haven't had it long enough. It doesn't cut quite as well as when it was brand new, so it will eventually wear out. I just don't know how long it will take.
Brad Goodall
Reviewed in the United States on November 8, 2018
Does its job, i usually run 1/4" depth cuts at 80-90ipm on this one.
Brian J.
Reviewed in the United States on April 30, 2018
This is a nicely made tool but is brittle. I needed to bottom out some drilled holes for replacing a door hinge on a Chevy pickup (the holes are extremely hard to drill). The hinges are spot welded to the frame. I drilled through the hinge to the frame with a cobalt drill and then used this bit to finish up the hole (the idea is not to drill through the frame at this diameter). The cutter lost a few chunks here and there but it did finish the job. Four holes.
Mr. Leoneitor
Reviewed in Mexico on December 9, 2017
La imagen no corresponde con lo que vende, el cortador es bueno pero la imagen que utilizan no es la misma que la del cortador
Muddy
Reviewed in the United States on January 9, 2016
SUPERLATIVE QUALITY!!! But (laugh at me):SADLY (just testing the idea), this is NOT a drill bit, I.E., it doesn't have a conical POINT to hold it steady. It is meant for a MILL.The idea of a precision carbide drill bit that could cut metal drew me to the flame with its allure.It has 4 points around the tip to cut with.So cool. So close. Sigh...
Robert L
Reviewed in the United States on March 2, 2014
I use the 1/4 inch 4 flute bit for cutting gator board and ultra board on a cnc. Running 250 inches per minute+ with a perfect cut. More than twice as fast as the 2 flute bits we use.
Recommended Products
