Your cart is empty.
Your cart is empty. Features:
This is a DIY charging Receiver module.
High-quality circuit board - CE/FCC/ROSH-certified.
Wide Compatibility - Suitable for all Qi standard phones.
Multi-level - Built-in short-circuit , over-voltage to ensure charging.
Comes with a magnetic spacer for better opertaion.
Specification:
Type: Charging Receiver Module
Model: TI
Input power: 5V 1A
Charging power: 5W ( ), compatible with 9V fast emitter
distance: 0-8 mm
Circuit board thickness: 1.1 mm (at chip)
Coil thickness: 0.3 mm
Distribution spacer: Approx. 46 * 36 * 0.4 mm
Implementation standard: Qi charging standard
Product Certification: CE/ FCC/ ROHS
Weight: Approx. 7g
Package list:
1 * Receiver Module
1 * Magnetic Spacer
Note:
charging = Transmitter + Receiver
1. Mobile phone that has charging function: For ios Phone8/8Plus/X or for S6/S7/S8/S9/Note5/Note8, etc., it has built-in ''receiver'' itself, or you already purchased the ''receiver'', you can recharge it by purchasing ''the transmitter (base)''.
2. The phone does not have a charging function: If your mobile phone does not have a ''receiver ()'', you need to purchase ''transmitting terminal (base) + receiving end (sMD)'' before charging.
3. Please note that our product is Receiver module. The transmitter is NOT included.
4. Please allow slight error due to manual measurement. Thanks for your kind understanding.
Scott M.
Reviewed in Canada on May 15, 2024
This onle worked for a couple of minutes then crapped out...not impressed
A. Calvin
Reviewed in the United States on March 31, 2024
It worked well for my uses.
Aaron
Reviewed in the United States on May 31, 2023
Product was poorly packaged. Arrived with one side of the coil ripped off the board. Soldered it back on but no joy, the unit is dead. Not worth the cost to return. I'd look for a different solution if possible, these are pretty fragile and looking at comments, a lot are delivered bad.
DALLAS ALBRECHT
Reviewed in the United States on October 20, 2023
The media could not be loaded.
Nolan Tenniscoe
Reviewed in Canada on May 25, 2022
Charges and works fine
Laurence K.
Reviewed in Canada on April 14, 2022
I wanted to make my tablet charge via wireless using this device soldered to the pogo pins on the inside. The back cover of my tablet was blocking the charge. I then put the device on the outside. Box tape also blocked the charge. It only can charge direct to receiver with coil exposed
ahmed
Reviewed in Canada on September 4, 2021
pour un sonim xp 57 et xp 8et autre
William
Reviewed in Canada on June 10, 2021
Works good, gets hot just like all inductors do.
Kindle Customer
Reviewed in the United States on March 8, 2021
Receiver doesn’t seem to work with any transmitter. Tried the 2 I have an home and 2 others my coworkers have, all run for about 5 seconds before they read an error and quit. “Wide compatibility” seems to not be true here.
Ettore Luberti
Reviewed in the United States on March 3, 2021
I've purchased 4 of these so far, and I've been able to add wireless charging to various devices such as Gameboys, headsets, and iPods. If you have any soldering skills and want to wirelessly charge your device, this module is small and compact to fit in almost any device.
J. Riesbeck
Reviewed in the United States on December 18, 2021
Charging receiver worked well in my custom application. I soldered the charging wires to a micro USB cable so it could easily plug into my device without modification.
William Stordeur
Reviewed in the United States on June 12, 2020
Good for small projects. Simple to use. Works.
Venesha Palmer
Reviewed in the United States on December 27, 2020
Bought this to put in a game boy advance, you have to solder it to whatever you're using it on but.i expected that, great product
Recommended Products
$599.00
$ 99 .00 $99.00