Your cart is empty.

6 Port PCI Express 2.0 SATA III 6Gbps RAID Controller Card, SATA 3.0 PCI Express Expansion Card Compatible for SATA6G 3G 1.5G HDD

4.6 (6) Write Review

Free shipping on orders over $29.99

$39.66

$ 19 .99 $19.99

In Stock

Qty.:

About this item

Compatible with Serial SATA 3.0 specification, backward compatible with SATA2.0 SATA1.0. Compliant with PCI-Express v2.0 specification and backward compatible with PCI-Express v1.0. Support Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3i.
Support FIS based on port multiplier switch or command switching. Compatible with SATA6G, 3G and 1.5G hard drives. Support Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3i.
The SATA interface mode of PCIE to SATA3.0 is AHCI mode. If you want to plug in the system disk on our card, the premise is that your system disk must be installed in AHCI mode when installing the system on the motherboard. Otherwise, the system cannot be started through our transfer card.
If it is determined that the SATA interface installation system of the system disk inserted in the motherboard is AHCI mode, then you can directly insert the hard disk into our card, and then enter the motherboard BIOS to set the system disk as the first boot.
If the two conditions are met, if the hard disk interface of the motherboard still fails to start, or restarts repeatedly, it may be caused by the conflict between the hard disk interface of the motherboard and our transfer card. The solution is to enter the motherboard BIOS and set the hard disk interface option of the motherboard to Disabled, then save and restart to start the system.

Product Description

Package List:

Riser card *1

Half height baffle *1

Name: 6-port SATA3.0 expansion card
Model: PCE6SAT-M01
Master control: for marvell 88SE92xx+109X
Interface: PCI-E 1x, 2x, 4x, 8x, 16x
Support system: for WINXP / WIN7 / WIN8 / WIN10 / LINUX
Bus interface: PCI-Express x1 slot
Expansion interface: 6 SATA3.0 interfaces
Product size: approx. 12 * 10 * 2cm / 4.7 * 3.9 * 0.8inch

Compliant with Serial SATA 3.0 specification, backward compatible with SATA2.0 SATA1.0.
Compliant with PCI-Express v2.0 specification and backward compatible with PCI-Express v1.0.

Support Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3i.
Supports communication speeds of 6.0 Gbps, 3.0 Gbps and 1.5 Gbps.
Admite FIS basado en conmutador multiplicador de puertos o conmutación de comandos.
Support FIS based on port multiplier switch or command switching.
Compatible with SATA6G, 3G and 1.5G hard drives.
Support for native command queue (NCQ).
Support AHCI1.0 mode and IDE mode.
Support hot swap. / Support 4 SATA.

The PCIE to SATA3.0 riser card is used as follows:

The system disk and PCIE to SATA3.0 riser card connection conditions and solutions:

The SATA interface mode of PCIE to SATA3.0 is AHCI mode. If you want to plug in the system disk on our card, the premise is that your system disk must be installed in AHCI mode when installing the system on the motherboard. Otherwise, the system cannot be started through our transfer card.
If it is determined that the SATA interface installation system of the system disk inserted in the motherboard is AHCI mode, then you can directly insert the hard disk into our card, and then enter the motherboard BIOS to set the system disk as the first boot.
If the above two conditions are met, if the hard disk interface of the motherboard still fails to start, or restarts repeatedly, it may be caused by the conflict between the hard disk interface of the motherboard and our transfer card. The solution is to enter the motherboard BIOS and set the hard disk interface option of the motherboard to Disabled, then save and restart to start the system.

The common disk and PCIE to SATA3.0 connection conditions and solutions:

When the system disk is inserted on the motherboard, the ordinary disk is inserted in the PCIE to SATA3.0 card, then only the adapter card information and the normal disk model need to be detected at startup.
If the condition is established, or can not start the system, then you must enter the motherboard BIOS, set the system disk to the first boot.

The system disk and the ordinary disk and PCIE to SATA3.0 connection and solution:

If the system disk with the original motherboard installed system is AHCI mode test, can use the following methods to achieve, if it is IDE mode installed system, then you can only reinstall the system through PCIE to SATA3.0 .
When the first condition is established, and you still can not start to enter the motherboard BIOS, set the system disk to the first boot.
When the first and second conditions are met, and you still can not start, then it may be integrated SATA interface conflict, please enter the motherboard BIOS to set SATA to Disabled.

Oswaldo Jimenez

Reviewed in Mexico on January 16, 2025

Hay varios detalles que debes de tener en cuenta al comprar este producto.1) no es RAID asi que si buscas RAID en el aspecto tradicional aqui no es.2) no es factible para hacer boot, asi que si tu estrategia es hacer boot con esta controladora entonces no es por aqui.3) Si se reconoce por el sistema operativo (use linux)4) a nivel profesional si usas CEPH no necesitas RAID para guardar tus datos, en ese escenario si puedes usar esta controladora de SATAS.5) una alternativa que puedes hacer es un RAID logico, osea desde el sistema operativoDesde mi persepectiva cumple con mis necesidades aunque debo admitir que lo compré mas porque decia RAID pero sigue siendo bueno.

Timothy K Knechtly

Reviewed in the United States on June 19, 2024

This is a good SATA controller. I tested it with 4 SSD's because that's all I had on hand. Despite the name it is NOT a RAID controller. I verified the controller chip part number that Windows reported is NOT RAID. If you're looking for a RAID controller card don't get this. I'm keeping this one in PC spares box.

Xenomorf

Reviewed in Canada on May 29, 2024

Installed it into win 10. Never even needed the disk that came with it. Windows recognized it as a raid configuration and set up the drives for me. Easy breezey.

Curran H.

Reviewed in the United States on March 5, 2022

Only drivers I could find for the device came for Windows. I don't use Windows, I am running Linux servers.

Mr Knight

Reviewed in Canada on March 15, 2021

I'm using it in a server built

ChillyKitten

Reviewed in the United States on January 17, 2021

All ports work but only 4 at a time, for the price I paid ($23) will keep it 🤷‍♀️