Your cart is empty.
Your cart is empty.10 Inch 80T Upgrade TCG Grind Aluminum Non-Ferrous Metal Plastic Saw Blade with 5/8-Inch Arbor,
david andrade
Reviewed in the United States on March 2, 2025
Used this to cut a 400mm piece of 4040 extruded aluminum down to 200mm each. Wasn't overly loud and did the job with little to no effort. I'll be cutting some 1/8 aluminum sheet next, but I wish I had some more extrusion to cut right now lol.
Brittney Withers
Reviewed in the United States on February 23, 2025
Used it to cut some 3x3x1/4in aluminum angle. Worked like a charm.
Wolverine
Reviewed in the United States on February 20, 2025
I purchased this blade to cut 1/4” plexiglass on my table saw. The cuts were smooth, with no chipping. It’s a good blade.
LegoDude
Reviewed in the United States on February 17, 2025
I recently picked up a table saw so I could start cutting acrylic sheets for display cases. From the reasearch I did online, I knew that the blade that came with the saw would not be ideal, so I found this on Amazon.Price was decent, so I gave it a shot. And it has worked very well so far. Cuts are smooth and clean, I'm not getting any chipping along the edges. Definitely does the job.
Mike Mathis
Reviewed in the United States on January 30, 2025
If you’re looking for a clean cut with aluminum extrusions such as 2020 2030. No cleanup needed.
HONEST REVIEWER
Reviewed in the United States on June 8, 2024
Please consider this an objective review. Some of the items can be reviewed by a simple one sentence. Sometimes I am brutally honest and that it is only my opinion.This is my review on the 10 Inch 80T Aluminum Non-Ferrous Metal Saw Blade with 5/8-Inch Arbor, Upgrade TCG GrindI am very happy with the performance of this saw blade while I have only used it to make cuts thru 516th metal I have made at least 50 cuts with it and the blade is a sharp as the first time I used it. The cuts are clean and smooth, for an economical blade it is tough.
Keven Audet
Reviewed in Canada on March 20, 2024
Il semble que la lame que j'ai reçu est croche ou mal balancé. Lorsque je la fais tourner avec la scie à onglet ça cause une vibration qui se ressent dans la poignée. Je n'avais pas se problème avec mon ancienne scie. Je ne recommande pas.
DA, AZ
Reviewed in the United States on December 23, 2024
I bought this blade for cutting 1/4" acrylic sheets and aluminum extrusions using by Dewalt contractor saw. On the acrylic sheets, it did a decent job although some of the acrylic was melting onto the blade. The cut edge was reasonably smooth. Then I got a 4.5 in x 1.5 in aluminum extrusion from 8020 that I was using to build a fence for my miter saw. This included 90 deg and 45 deg cross cuts. The cuts were clean and smooth. Very impressed with this blade.
Lisa R
Reviewed in Canada on November 8, 2024
I bought this to cut my aluminum deck posts and it's been working perfectly fine. As long as you remember to install it "backward" (the label is on the opposite side to standard saw blades), you should be able to get the most from this blade. It was well worth the purchase.
mike_oooo
Reviewed in Canada on October 9, 2024
10 Inch 80T Aluminum Non-Ferrous Metal Saw Blade with 5/8-Inch Arbor has about a 3/4" arbour hole vs. the 5/8" as advertised. Returned product and will not purchase from this seller again.
Martin
Reviewed in the United States on February 28, 2023
I purchased this blade to cut a 1/8 inch thick 60 inch long polycarbonate sheet. The triple chip grind teeth on this blade did an excellent job. The cut was completely smooth, with no chipping. The resulting edge was smoother than the other edge that was factory cut. There was no melting of the plastic, despite the slow feed rate I used. I was not feed rate limited, I just chose to go slow to avoid any chipping. I would have given the blade five stars, but one of the raker teeth was chipped. While I would have preferred an unchipped tooth, the cut was excellent nonetheless.
Recommended Products
$31.55
$ 14 .99 $14.99
$35.99
$ 15 .99 $15.99