Using these on micro RC planes (Volantex Ranger 600sp, 400mm T-28, Cub).I cannot find a pre-made mount (plenty with 14mm width, this is 20mm) anywhere.Have it zip-tied to top of plane which is pretty janky.Get ~500' of range, without obstacles, on 25mW setting with Fatshark Recon headset.Good Field of View.Going to DJI soon so this'll be the last of analog FPV for us.

Great little units ...250mw offeres 600' range w ferry little break up ...please continue making ...perfect size for FPV ..100mw would be nice ..25mw just not enough

I wish I got this some years ago when I saw they were released. It is super easy to install and use. I just use scotch tape, double sided foam tape or zip ties, the button on the camera, and cheap betafpv vr02 goggles and its buttons to find the channel, pretty straight forward. The camera quality is good for this price and I get reasonable range with little interference (at least a football field length, don't want to go much further anyway for micro/mini aircraft in case something happens and have to go searching). I see many reviewers say it doesn't work, can't see through the noise. Maybe their reading comprehension, as mine, was the culprit because the instructions do say "powering on the vtx, blue LED display 0, indicating the vtx is powered on, but it is in off status without any transmission", I was getting the same terrible signal some say it has. Surprised I got any at all now that I know why. I changed it to 3 -'s stacked to get the most power (i thought it was supposed to show in goggles but finally looked at the display on the camera's board). It goes further than my micro whoops that say they do 200mw and those can go to the ends of my flying area no problem.It does get quite toasty and may be fragile if exposed to impacts as the antenna can get bent or lense scratched of course.My main complaint though is I wish there was at least some voltage display (of camera battery) so I know when it is about to cut out. There is no warning or indication it is low, just stops. So be prepared to go looking when you lose feed and hope it wasn't far and you can remember the area good, or you have record feature on your goggles so you can at least get close and hope it didn't glide far from there.A timer should be used depending on the battery size for the camera, which of course requires trial and error but there is also a list of current ranges for each power mode in the instructions for general idea. I recommend at least a 200mah for about 5 minutes highest power, and of course larger for larger aircraft that wont lose much flight time or have it at least covered by camera being remaining on when aircraft thrust battery is out. Or make a parallel adapter on the aircraft's power connector so camera can plug into 1 main battery.Also, the lens is a bit distorted for wide angle fisheye effect making distance judgment not very easy (everything is near on the edges but far in the middle, stretched in between) Of course they glue it in place with no option to remove it unless you want to start cutting.I also wish the antenna was detachable (so it can be inside aircraft while camera is outside through small hole), and the camera reversible so I can have right side up view while the unit is upside down (like for camera in cockpit window and antenna down in body). It can really affect aerodynamics with its drag and weight relative to smaller models.Anyway, sure there's these issues but I was not expecting the feed quality and range it has, not bad especially now it's down to $25, can't expect much better.

Very good for light aircraft

The packaging was decent, the instructions were easy to follow and was able to set it up and get it running in about 2-3 minutes. The camera quality is decent for its size. The range at max is pretty good and will not loose signal when going behind a couple walls in your house. The speed is pretty good and it feels like there is little to no delay from the goggles to the vtx. The only things to keep in mind is that the unit gets very hot when used at max power and the antenna is easy to bend so be careful when setting it up. Otherwise it’s a quick and fun way to add a VTX and Camera unit to your drone or rc car.

I didn't have very high expectations when I got this. I just needed something cheap and easy to throw on my rc planes and this seemed to do the trick. I'm actually really surprised at how well this works. The picture quality is surprisingly good and it super simple to set up. Just plug in a battery, set the frequency and your good to go. I haven't tested the range on it yet but it seems to hold up pretty well with minimal breakup when within 100 feet.The only thing to really be aware of is that the VTX gets really hot pretty quickly so definitely mount it somewhere that won't melt or be damaged by heat and also get some air flow over it as soon as you can.Overall I'd recommend this for anyone just wanting a quick intro to FPV.

No easier way for fpv on a drone or rc carMy monitor connected quickly and it works great

I use a few different types of 1s lipos, and these Wolfwhoop WT03 are perfect. I've bought a few in past and still come back to this specific model. Why? Well... The milliwatts is adjustable, and the higher milliwatts isn't always good, due to the radius of the output (bubble). Too high and you can't get too close with your FPV gear, so the key is having diversity on the googles with RHCP matching and a patch antenna as well.Anyways, works as intended, cheap effective and I can easily to long range FPV with no issues.

中国製なので 未だに 到着してない

I purchased this so that my son can FPV using surface vehicles (from 1/24 to 1/10 scale). It was very easy to set up, thanks to the integrated antenna, but I did need to get a BEC to regulate the voltage of my RC's ECS from 6v to 5v so it can run right from the receiver box.I removed the included plug and soldered on a Futaba servo plug for ease of use, but before that, I was able to use a small 1s lipo to power this, then I tried 4 x AA (NIMH rechargeable at 1.2V each) with success).Selecting the channel and power is quite easy and while most of our driving is through walls, the signal strength and quality have been quite good.We did 3d Print a case for the camera as it's just bare circuit board, but it's light enough to mount anywhere (we use double-sided tape so we can move it from car to car).There is no on-screen-display (OSD), which is a little bit of a bummer as I would have liked to have seen a voltage meter at the very least if I decided to run this off a separate battery pack again).Overall, I'm quite happy with this little guy. The latency is very low (at least for surface RC) and the quality of the picture is better than I expected.

I bought two of these cameras with built-in transmitters. I installed one on my modified Inductrix (Tiny Whoop) after the old camera I was using died. Installation was just as easy as the first time around, but this time I was able to set the transmitter power to 50 mw instead of 25 mw, which made a real difference when flying indoors. No more video loss!I installed the second one on a 1/10th scale RC car (just stuck it on the wing with some double-sided foam tape) and set that one to transmit at the 200 mw level. It has great range! I actually lose RC control before I lose video on the car. This is a perfect camera if you're building an indoor racer (quad or RC car), and I think it would probably be OK to use on a small outdoor racing quad as well. For sure it's more than good enough for a dirt track FPV race truck or buggy.Setting the transmitter frequency is very easy thanks to the blue LED display. And the video quality is surprisingly good, especially considering how small and lightweight the package is.For this price, I'm absolutely thrilled with the performance.