Your cart is empty.
Your cart is empty.Product Description
This Dryer Repair Kit contains all of the parts that are commonly defective when your dryer is noisy. This kit is a universal repair kit for 27-in wide dryers built from 1965 on. Kit includes (1) dryer belt, (4) drum support rollers, (1) idler pulley, (9) roller tri-rings, (1) clip, and instructions. This accessory can be used with many different brands and models; check your model number to confirm compatibility. Installing this accessory kit will require basic hand tools and novice repair experience. Be sure to unplug the dryer or shut off the house circuit breaker for the appliance before installing this accessory.
From the Manufacturer
Everything you need for Do-It-Yourself dryer maintenance and repair.
C.C.
Reviewed in the United States on March 9, 2025
Perfect fit for my 14 years old dryer. Highly recommend buying the kit and replace belt, rollers and the "white" pulley. Especially if you are taking the dryer apart. Pay attention to the moving parts - rollers and the pulley. I noticed a little more free spinning with the new rollers, the replacement is probably not needed (I did it anyway since I got them and won't have to deal with it for while). The pulley did not spin, I believe that contributed to the shredding of the belt... the belt is probably old and cracking anyway. There are several videos on YouTube. I did not open the back or from the back as I did not want to pull out the stack-able and there is not enough room for me to get between the dryer and the wall to pull out the back pane. I worked on the dryer when the dryer is on top of the washer. It wasn't hard to work it while dryer is stacked. According to the packaging, it is made in the USA.
Taylor Carter
Reviewed in the United States on March 5, 2025
Appears to be oem parts. Belt is labeled made in USA. Installed in my dryer and now no more noises. I had purchased another kit on here before this one that was complete junk. The rubber on the rollers are soft like they are supposed to be. The retaining triangles look exactly like the ones that were in my dryer from the factory. Definitely would buy again.
matt mailhoit
Reviewed in the United States on March 11, 2025
30yr old dryer working like new . This kit with all rotational parts is cheaper than an incorrect Chinese belt and idler. No brainer , took 15min to install entire kit .
D
Reviewed in Canada on March 10, 2025
The parts are as described and great quality if you need drum rollers and/or a belt. If your pulley wheel is squeaky though, like mine was, you may want to buy the W10837240 Dryer Idler Pulley instead as it comes with the pulley arm and shaft, not just the wheel.
Jerry
Reviewed in the United States on February 17, 2025
SKIP aftermarket parts, definitely go with OEM. Our drier burned out the thermal fuse, and because that generally only happens if there is an underlying problem I decided to investigate. After confirming the fuse was bad I removed the front panel and drum of our drier to find one of the drum rollers chewed up pretty badly and wasn’t spinning freely. I bought this kit with new belt, tensioner, both rollers and hardware. I did completely clean both roller shafts well and added a dab of grease to the bushing on both. These rollers are not equipped with bearings, so greasing them lightly seemed logical. Took about 20 minutes to remove all old parts and install new ones, another ten minutes to reassemble the cabinet. Replaced the thermal fuse and drier fired right up and ran smoother and quieter than it has in years. After reading reviews of the many aftermarket parts I’d found there was no way I was skimping on price for an appliance that uses 220V and creates high heat- super risky. Plus I didn’t want to do this repair again in short order. So I didn’t mind spending the extra money for OEM Maytag parts, plus the fact it was a repair kit was outstanding.If you’re embarking on this repair, you’re already very deep into your drier. This is a perfect time to remove all lint, and thoroughly clean and inspect the entire unit. I checked all of the following- high and low heat cutoff switches, removed the entire exhaust box and inspected the fan and cleaned all the plumbing. Inspect your vent hose and clamps, all fasteners, and electrical connections. Our drier is 11 years old, and this is the first repair we had. We removed about $7.00 worth of loose change, various pieces of misc. hardware (not drier related), a couple buttons, a whole bunch of rogue lint, and other dirt. Most of this is extremely hazardous around heat and moving parts. All in I would definitely buy these parts again (just hoping I don’t have to), it’s so much easier and more cost effective to repair than replace an entire unit. I learned that every couple years I will be removing my front drier panel to thoroughly clean and maintain the moving parts. I’d say this is a super easy DIY repair with basic tools, and while the kit came with instructions there are plenty of videos online as well.
RideUtah
Reviewed in the United States on January 9, 2025
My dryer started making a horrendous squealing noise. Most people start looking for a new dryer at this point, but reviewing online it didn't look too difficult and the noise is usually either the wheels inside or the belt. I found an online video that walked through the process, ordered this kit, and proceeded to strip down my dryer. It took me about an hour as I've never torn apart a dryer before, but online videos helped a lot. All of the needed parts were in the kit. My problem ended up being one of the wheels under the drum, but I replaced all and the belt while I was in there. As a bonus, I cleaned up 20 years of built up lint inside the dryer!The instructions with the kit are fairly minimal and not great if you haven't done this before.NOTE: The clips on the wheels are by far the hardest part of the job. As long as your kit comes with all the clips you need, it would probably be easier to just cut or break off the old clips.We are now 3 months later and the dryer is working perfectly, saving me hundreds on replacing it with a new one.
GregBooks
Reviewed in the United States on January 8, 2025
These fit our Kenmore dryer perfectly, as they are OEM parts. It is worth the little extra cost, as they are simple to install. This is the second time that I have bought these, as the roller seem to wear out every 5 or so years. While it is not a difficult job to replace the roller wheels, you do have to take apart most to the dryer to get to them (at least with our dryer). All said and done, I was able to change out all of the parts in under an hour with a few simple hand tools (screw driver and nut driver).
Adventure Human
Reviewed in the United States on August 6, 2024
Perfect match for my Staber Dryer. Plastic bag that parts came in was open, small parts fell under the washer… Would have ordered the “gently used” if I would’ve known. Had to tackle the mound of clothes so I didn’t return.
pgokou
Reviewed in Canada on June 17, 2024
Fixed mY squeaking dryer. And they are Original whirlpool parts.
Heavy D
Reviewed in the United States on November 8, 2024
This was crazy easy to install. The old rollers were worn out and sloppy on the spindles. The dryer made ungodly noise while running and also shook a bit. After install, it is whisper quiet and smooth running.I also used a dry film lubricant on the spindles and inside the wheel bushings. Hopefully extending the life.Genuine parts at a great price. I’m buying a second kit to keep on the shelf.
Ozium
Reviewed in Canada on March 30, 2020
This is just what our dryer needed. One of the bearing/wheels was worn down and causing the belt to slip. The job does take about an hour but well worth the savings. The only thing that I noticed is the belt is not as thick and wide. It works, it just won't last as long as the OEM belt.
Jay
Reviewed in Canada on February 27, 2020
It’s been a month now after I replaced the broken parts, no issues so far. The product is good & easy to install.
S. Wei
Reviewed in Canada on November 20, 2016
The parts works great, but as soon as you open up the dryer, you see everything is cheaply made. It gets you mad! You pay a thousand or more for a "quality" product, and what you get is really flimsy sheet metal shell, medieval level of engineering, plus a fancy control panel.Like, you really want to ask them... "Have you ever heard of a thing called BALL BEARING or ROLLER BEARING?" If my power tools are made the way these pieces crap does, they will most likely blow up the second I power it on...
Recommended Products
