Your cart is empty.
Your cart is empty. Specifications:
Description:
Designed with k type connector, insulated wire.
It can be used with k type digital thermometer to measure temperature of air and gas.
Arthur Ludwig
Reviewed in the United States on October 3, 2024
I have an ideal meter and the plug does not fit. I should have been more careful.
MRA
Reviewed in the United States on December 11, 2022
Product was as advertised! Very good value!
Life’s a Beach
Reviewed in the United States on October 28, 2021
One of my Tenma meter leads failed so I bought these. They work like new. Replace them in pairs if you want accurate comparison of two temperatures. They do not perfectly match my remaining old lead but it doesn’t matter as the match each other.
Nicolas
Reviewed in France on June 10, 2018
Testé au feu du briquet, dans la chaudière, dans la piscine, dans l'air, dans le congélateur, un peu partout quoi...Et ça fonctionne !NB : si le bout se casse, on peut re-torsader les deux fils ensemble et ça remarche : c'est la magie du thermocouple !!!
Tobias E.
Reviewed in Germany on March 8, 2017
Bei den 2 gelieferen Thermoelementen war bei einem bereits der Draht an der Messstelle abgebrochen, deshalb auch die schlechte Bewertung.Der andere funktioniert, auch wenn ich den Eindruck habe, dass der Stecker etwas zu dick ist und die Anschlüsse vermutlich etwas kürzer sind als sie sein sollten. Soll mir egal sein, in mein Gerät passen sie zum Glück trotzdem.Über die Qualität der Messergebnisse kann ich keine Aussage machen, da mir hierzu die Vergleichswerte fehlen.
Tomlang
Reviewed in the United States on May 6, 2015
Worthless. Tiny wire probe at the end of the thermocouple is easily damaged. Programmed temperature and realized temperature as much as 50-degrees in error. Error so badly in error that controlled heat blanket burned and almost ignited product bring heated.
Andrew J. Manning
Reviewed in the United States on September 26, 2014
Meets expectations. No problems, just nothing exciting. Delivery was okay.
Tilgore Krout
Reviewed in the United States on August 11, 2014
I got this to replace the worn out probe that came with the electronic thermometer that I used with my coffee roaster. It seemed awfully cheap but I gave it a shot. Good gamble. It works fine and is higher quality material than the original. Or at least it seems sturdier. Thank you, internets!
Rl Shuey
Reviewed in the United States on March 28, 2014
They work, but there are a few things I don't like, such as: the wires are really too stiff, the welded ball on both are not great in fact one is very poor, one of the wire's strain relief does work and the wire twists back and forth where the wire inters the connector (if I use it much I'll have to fix it to keep the wires from breaking). I bought them for just for backup, so I'll be keeping them, but I just wish they were better built!
T. Mccleary
Reviewed in the United States on November 11, 2014
I have a Fluke 87-V multimeter, and I wanted to get a couple of cheap type K temperature probes for general measuring. To check for accuracy, I set up an icewater bath in an insulated cup, using reverse osmosis filtered water. This water bath should have a temperature of 32.0F. The probe which came with the meter stabilized at 31.2F, while these cheap probes read 30.0F (probe 1) and 29.8F (probe 2). This is ok comparison, as the meter itself lists an accuracy of +/- 2.2C (about 4 degrees Fahrenheit). The construction quality appears ok. The picture on the amazon page shows a replaceable connector, but the sensors I received have a one piece molded plug
Recommended Products
$32.49
$ 16 .99 $16.99