Your cart is empty.
Your cart is empty.Big Dave
Reviewed in the United States on August 21, 2024
This looks exactly like the one that came off of it, including the logo.I initially thought it was plastic until I removed the broken one from my phone.It appears to be a very thin glass laid over a thin plastic mold.If it isn't OEM, it's a very good copy.
J.D.
Reviewed in the United States on January 27, 2024
This is an easy enough install. However, the pre-applied adhesive will not hold the glass to the phone. There will be roughly a .5mm gap. After just a few hours of use that gap will release the glass.I recommend buying additional 2mm/3mm adhesive tape and possibly some black T-7000 glue.Also the LED and sensor found inside the lens housing has a delicate ribbon cable. If you're not comfortable removing the LED and sensor from your original lens housing, you can simply push out the lens housings from the glass with a little heat and swap them with ribbon cable still attached.If your lens housing is damaged, remove the LED and sensor by picking at the adhesive from the opposite side of the ribbon cable. Once the adhesive begins to pull up, gently pull, working your way down to the LED. Make sure that when only the LED is left adhered to not pull against the ribbon between the LED and sensor. You'll have to gently pick under the LED.
Abel Cruz
Reviewed in the United States on September 12, 2023
Initially it installed very easily and it looked beautiful. I loved it and showed it off to everyone. Except for the fact that the glass was very brittle and it was glass, not tempered glass. It lasted about a week and it broke because I had it in my back pocket and I sat down and hear a crack. Would not recommend
A. Shook
Reviewed in the United States on June 7, 2023
Installed my back glass 3 days ago, and just the pressure of it being in my pocket and in a case while walking caused it to break in the lower corner. The fit does not quiet exactly match on the phone and I ensured all of the old adhesive from the glass was removed prior to installation.
Samson
Reviewed in the United States on October 12, 2023
Good Quality, just need to swap out the lens assembly from the original, which was super easy with a torch. Just gently apply heat until the adhesive softens and apply firm but gentle force until it slowly lets go. Stick in the original lens and light assembly and good to go. Having the adhesive rubber pre applied to the glass was a nice touch. Color,markings, fit, and finish are indistinguishable from the original Nebula blue glass it replaced.
D. Hussey
Reviewed in the United States on August 15, 2022
So I had to buy two of these, so good deal for this company. After watching online videos, since this company has no instructions, I followed the one that said to remove the camera lens and flash from the new glass, and replace with the old one ( presumably to make it easier). The problem is while pressing our the lens one the new glass, it shattered. Maybe more heat would've prevented this, I don't know.Ordered the second one and this time carefully removed the ribbon cable attached to the flash on the old glass, and attached to the new one ( another video on YouTube). Heat helped a lot to loosen this, and tweezers for it off.The rest of the replacement went fine. Key points:. Use a heat gun. Clean off all old adhesive from the phone. Throw away the useless tools that come with the glass ( why do they include 3 Phillips head screwdrivers for a glass removal?). Use heat, a knife blade, tweezers, and patience. It really wasn't that bad, and the new glass looks great ( it has the oneplus logo and name, not seeing listing).
alexzzz
Reviewed in the United Arab Emirates on March 19, 2022
The one i ordered (Clear) does not fit the One Plus 7 Pro. The housing for the sensor between lens 2 and 3 is not there. In the picture it is shown but not on the actual product. Better find a replacement.
mark sutton
Reviewed in the United States on August 4, 2021
It was a pain in the ass to install. Figuring out which part of the old camera lens assembly needs to be saved and installed into the new cover took a few minutes. A reminder: This kit does not include instructions. Also, I have never replaced a glass back cover on any phone ever before. One of the reviews on here mentioned something about heating with a hair dryer. That being said, I was able to remove the old cover with the included plastic tools. I used alcohol and one of the tools to scrape off left over old adhesive. I removed the part of the camera lens on the old cover that has the wire attached in the same manner and simply dropped it into the new cover. I removed the strip of film from the adhesive on the new cover (stop and make sure wire to lens assembly is routed nicely and not twisted...it will be visible from now on!) and pressed it onto the frame. Done. I got the clear one and it looks great!!
Rafel
Reviewed in the United Arab Emirates on February 22, 2021
Easy to fix, like original
Hatim Amin
Reviewed in the United Arab Emirates on January 27, 2021
This case unlike others, has the oneplus logo on it, looks exactly the same to the original, and also gives that matte depth effect. Which other replacement back cases do not. But do note that the glue is not very strong so appy your own glue over it. Also do not use its flash and camera lens, replace your original lens and flash into it. Lastly, if you want to remove the original back cover or the camera lens, heat the case to easily remove it without damaging the phone in any way.
Sabrina
Reviewed in the United States on October 19, 2020
This is infinitely better than the one I previously bought off Aliexpress. The adhesive on this one is a nice dark black and is cleanly cut and very strong, no unsightly bubbles. Glass seems durable and resists fingerprints very well. The cheap Aliexpress one had really crappy adhesive and broke within 3 weeks (with a case on!). It was also a total fingerprint magnet.This one is excellent quality at a fair price. Look no further!
Recommended Products
