Your cart is empty.
Your cart is empty.
Included in the Kit:
50 of 7 mm Clamp, Part No. 16700001
50 of 10.5 mm Clamp, Part No. 16700006
50 of 11.3 mm Clamp, Part No. 16700007
50 of 13.3 mm Clamp, Part No. 16700010
50 of 15.7 mm Clamp, Part No. 16700016
50 of 17 mm Clamp, Part No. 16700017
Genuine Oetiker Clamps
Stainless Steel, Material no. 1.4301/UNS S30400
What is StepLess Technology?
Oetiker invented the StepLess ear clamp in 1979. The ear clamp’s special design eliminates steps and/or overlaps on the inner circumference of the clamp for a 360° leak-free seal. Because the tongue resides in a groove, the “tongue-in-groove” feature exerts pressure on the assembled parts over 360°, enabling the clamp to apply a continuous radial force completely around the connection’s diameter.
Mechanical interlock
The interlock is a mechanical system for joining the clamp ends to permit closure. Some interlock designs can be opened for radial installation prior to closure.
Clamp diameter
The following applies as a guideline: To determine the correct clamp diameter, push the hose onto the attaching material, (e.g. the nipple), and then measure the outer diameter of the hose. The value of the outer diameter must be slightly above the average value of the diameter range of the clamp to be selected. The listed size of the clamp denotes the inner diameter (id) of the clamp.
How to Install
These clamps can be easily installed using Oetiker Hand Installation Pincers (HIP). The HIP tools have been designed especially for pinching ear clamps quickly and easily.
Oetiker HIP Compound Action, Standard Jaw Pincer, Item No. 14100386
Oetiker HIP Compound Action Side Jaw Pincer, Item No. 14100387
Oetiker HIP Single Action Standard Jaw Pincer, Item No. 14100396
How to Remove
Ear clamps can be easily removed using Oetiker’s hand clamp cutter (HCC). The HCC tool is designed to safely remove ear clamps.
Oetiker Hand Clamp Cutter, Item No. 14100407
Please Note: The clamps included in this kit are not designed or intended for use in PEX applications. The sizing references for PEX clamps are not the same as standard Oetiker clamps. Oetiker PEX Clamps should be used for PEX applications.
TT
Reviewed in the United States on February 2, 2025
Very good quality. If you are looking clamps like these, just get them.
PolarBear
Reviewed in the United States on September 23, 2024
I have had this in my want list for a while but just happened to be out of stock when ever I looked. Finally came back up and I bought it. Nice to have a large selection of the pinch clamps in a plastic box.I didn't do a breakdown of the cost of the clamps, but it seems a bit expensive. 4 stars was for price only
welder314
Reviewed in the United States on March 5, 2023
I wasn't 100% sure what size I needed for the hose I was using, so I just bought this kit. Turns out I was correct anyway, but now I have a bunch of good clamps for future use. This is a good assortment, and I'm sure I'll use them eventually.The hose I'm using is Gates 6LP350X, with a spec outside OD of 18.8 mm. Actual measured was around 19.0 mm. The clamp that fit was the "21mm" clamp part number 16700024, marked with the number 21 on the clamp. I also tried the 19.8mm clamp on a short piece of spare hose, it fit, but not as good as the 21. It was nice to have the various sizes, and now I know that the 21 was actually the "best" size to use.
Edward Eplett
Reviewed in the United States on April 23, 2023
👍
Marshall Nichols
Reviewed in the United States on December 20, 2022
Nice assortment, good quality, wish the pinch took came with it.
ANAHI L.
Reviewed in Mexico on December 2, 2022
Buen conjunto de abrazaderas Oetiker un poco difíciles de encontrar en esta marca especificamente, trae 40 piezas en total ( 10 piezas en cada tamaño), en 4 tamaños (7, 9.5, 11.3 y 13.3 mm). Son de acero inoxidable se ven de buen acabado. Se utilizarán para aplicación automotriz aunque se pueden aplicar a cualquier necesidad. No son reutilizables son para aplicación que requieran fijación permanente, no dañan mangueras a diferencia de las abrazaderas comunes de tornillo. Veremos cómo resultan a lo largo del tiempo, por lo pronto todo bien con el producto.
Stingray
Reviewed in Canada on June 29, 2020
Conforme a mes attentes.
John H.
Reviewed in Canada on January 5, 2020
Not what I wanted
Kevin
Reviewed in Canada on June 14, 2019
Did the job, will do future jobs too!
Customer
Reviewed in Canada on March 16, 2019
Nice set
Dwain McArthur
Reviewed in the United States on January 13, 2019
Purchased with Oetiker pliers. Great addition to my toolbox. Customers prefer the "clean look " of these clamps on their bikes. These work so much better than "worm clamps" . Must have for BMW and Ducati service techs.
vkdriver
Reviewed in the United States on July 10, 2016
Couldn't source these locally. Brick and mortar stores weren't interested in ordering, so I ordered this kit. More than I will ever need, but I have all that I will ever need. Quick, fair price and quality product.
h. johnson
Reviewed in the United States on September 3, 2015
Excellent product replacement for the worm gear hose clamps. Used with the Ideal-Tridon crimp clamp tool. Creates a very positive leak free connection. Used on fuel supply lines for Amal carbs on 1960 Triumph T120. Will be purchasing additional clamps to use on varied automotive and motorcycle applications.
Recommended Products
$24.49
$ 11 .99 $11.99
$27.23
$ 13 .99 $13.99
$56.99
$ 29 .99 $29.99