Your cart is empty.
Your cart is empty.Product Description
Product description:
- Gikfun Packing 5pcs RFP30N06LE 30A 60V N-Channel MOSFET TO-220 ESD Rated
Lord Frank Bonami
Reviewed in Canada on March 18, 2025
Rated for arduino I thought they would truely be logic level capable. Yet they are NOT. The arduino cannot fully turn them on and simply makes them get hot instead of driving the load.
Mathieu Casavant
Reviewed in Canada on February 9, 2025
My big concern was to see if it would work with a 3.3v from a Pi since some comments said that it would not.For me it worked perfectly. I did connect the ground of the Pi with the ground of the power source and I also connected the source to the gate with a resistor.
HK
Reviewed in Canada on February 7, 2025
I did not start to use yet. But it looks good.
Matthew Owen
Reviewed in the United States on July 28, 2023
Does not work with 3.3v supplied by Raspberry pi, though "RFP30N06LE" is supposed to. Spent a day trying to figure out why my circuit did not work, until coming here!Do not purchase this if you want to use it with the raspberry pi!
Anatoly Butko
Reviewed in the United States on March 27, 2023
I doubt i can return soldered a few times mosfets trying to figure out where i was mistaken before i decided to check what exactly they are. Vt must be My regret is not a few lost bucks, it is a few lost hours of my own life.
Electronic Technologist
Reviewed in Canada on February 11, 2022
Yup they worked as expected.
Josef A. Wainz
Reviewed in the United States on January 15, 2021
These N-Channel Mosfet seminconductors worked as expected. They were packaged and delivered nicely. We have them working with an Arduino project.
orlie Perez
Reviewed in the United States on June 22, 2020
easy to connect work great . I like using these on my displays I build small house and light them up . this gives me a chance to give an fast sample for show the little houses .
Mike
Reviewed in Canada on April 17, 2020
Really good, easy to use and respond to -5V logic signals on the gate. Very low resistance between drain and source so very little heat generation with battery powered devices (1 to 5 amps)
Arturo Sepulveda
Reviewed in the United States on August 5, 2019
As expected
Austin
Reviewed in the United States on June 14, 2017
Very easy to use with an Arduino ~5V digital output to turn anything in a DC circuit below 30A on and off. That includes basically anything you can think of related to small electronics projects. It switches incredibly fast, so you can use it for dimming with PWM as well. The connections can be potentially misleading with this MOSFET. Without reading into the details, you would expect to connect the 'drain' connection in the middle to your ground or your lower potential side of your circuit and the 'source' connection on the right side to your higher potential power source. However, that won't work. The current will just flow through regardless of the value at the gate. So connect the gate to your digital output of your Arduino, the 'source' pin to your ground or lower potential side, and the 'drain' pin to your higher potential side or power source. For instance to power an LED, the connections in series might be ( +5V --> MOSFET drain pin ) and ( MOSFET source pin ---> LED ---> Resistor ---> Ground).
T-Mart
Reviewed in the United States on March 18, 2017
Work flawlessly for an Arduino-controlled railroad crossing signal that uses truck taillights for warning lights.
MongoGrubb
Reviewed in the United States on March 1, 2017
Great product that meets all specifications and details per layout. Worked great to replace a very similar MOSFET that fried due to poor engineering on the motherboard manufacturer's part. I had to add a heat sync but it still works great.
Recommended Products