Your cart is empty.
Your cart is empty.Product Description
Durable Vinyl Garage Door Replacement - MD Building Products 08460
From the Manufacturer
Deluxe model bumper style threshold with built in vinyl seal. Heavy duty aluminum and vinyl design assures years of protection from the elements. Installing a threshold will help to seal out drafts from the bottom of your door. Helps make your home more comfortable and saves energy.
Warren L
Reviewed in the United States on January 29, 2025
I have a fifty-year old home and this item was the exact replacement for an original threshold. Image shown on Amazon matched exactly to the piece needing replacement and worked perfectly.
Dean H.
Reviewed in the United States on February 21, 2024
Used this for an outswing exterior door and it worked great.
James Sawada
Reviewed in Canada on December 12, 2024
Better than going to home depot
Customer
Reviewed in Canada on November 2, 2024
Solid and as described
Customer
Reviewed in Canada on August 22, 2023
good quality , easy to install
Kevin Meffert
Reviewed in the United States on July 2, 2023
Best compliment is... we would purchase again.
Eduardo Sanchez
Reviewed in the United States on July 1, 2023
Cambio Viejo,por lo nuevo.
AnsiDrop
Reviewed in Canada on April 27, 2023
This threshold is durable, made from thick metal, and a good draft stop for your door. I had about a 3/4" gap I needed to fill that was letting in cold air. After trimming this to the size of the doorframe and screwing it down it worked like a champ. Would recommend this product any day.
2sweet4u
Reviewed in the United States on October 9, 2022
I needed it for the back porch door . I measured it for the half inch height / width . I am by no means a carpenter. Three screws included and I now have a threshold to keep weather out . Thanks
fixitall123
Reviewed in the United States on March 11, 2021
The media could not be loaded.
laekelley
Reviewed in the United States on April 2, 2020
If you have to cut this down in size to fit your opening, the outside holes are so close to the end that you may have to cut them off. Would be better if it were a five hole design or of the outside holes were closer to the center.
Simon
Reviewed in Canada on October 27, 2019
Exactly as shown. Made of heavy-duty aluminum with 3 recessed screw holes. Expect it to last a lot longer than a plastic alternative... Even though I had to cut off 1.5 inches on each side to fit it in, I could still comfortably use the end holes as they are made over 2.5 inches away from the ends. I like the fact that there are rubber seals along both front and back. See photos for additional details on the product and rubber seal.
Wizengy
Reviewed in the United States on November 18, 2018
I used this as a transition between tile and the outside at the door so that metal part is a little above the tile. This is a solid aluminum extrusion with enough 'rubber' to seal the threshold from the elements. My door is 32" so a hacksaw and miter box made quick work of it. Make sure you cut a little from each end to keep the screw holes centered. I did not need the rubber door bumper so I removed it leaving only the little round part between the metal and concrete and tiled just next to this piece. I used blue tapcon screws to anchor it and added some epoxy for good measure. Added silicon caulk between the tile and this piece. The door sits above this piece so that the inside of the door is near the square edge. I also used https://www.amazon.com/gp/product/B000I199Z8 on the door to keep the buggies out. For this I needed to add a tiny ramp on the floor to keep the square metal lip from pushing the rubber door sweep out of position.
Recommended Products
$23.19
$ 11 .99 $11.99
$15.62
$ 6 .99 $6.99
$39.99
$ 18 .99 $18.99
$129.95
$ 63 .99 $63.99