Your cart is empty.
Your cart is empty.Product Description
V CisxviLC Engine Splash Shield Guards, we will protect your car's chassis and engine. Let you drive with peace of mind.
Using the most economical way to solve the above problems for you, the vehicle will last longer and be more reliable. This will be a worthwhile choice for you.
Our Engine Splash Shield : Excellent hardness, no deformation during impact
Our Engine Splash Shield : Anti scratch, wear-resistant, and corrosion-resistant.
Our Engine Splash Shield : Sharp tools cannot penetrate
New Under Engine Cover Directly Replace Original
The new Engine Guards Plat has high hardness. The Original Factory's Engine Guards Plate has low hardness and is prone to deformation.
New Engine Cover thickness is four times the original
New Engine Guards Plate increased thickness and use of harder materials
New Under Engine Cover It's difficult to break through
The new Engine Guards Plate is difficult to puncture, providing better protection for your engine .The Original Factory's Engine Guards Plate is easily punctured by stones or sharp tools.
pheonix_rise
Reviewed in the United States on August 5, 2024
It appears to be made adequate, but overlaps the frame and has no center hole for the rear. Best to purchase replacement plastic clip to replace the worn out ones. Had to drill a hole to fit the rear center fastener. It overlapse the old Ford plate nearly exact save the rear side joggles the new one has none or any foam to cradle the hydraulic pump or molding to cradle the intercooler tube, not that the old one did considering it sagged so much and was delaminating. I've seen a bunch of cars within dragging on the ground. The new one is a bit more flimsy than I would like personally. I'm thinking about putting a piece of aluminum right down the middle of it to keep it from sagging. Simple to install.
D. Faulkner
Reviewed in the United States on August 4, 2024
2017 SE, it fits great and its robust. Looking forward to not having to drop the whole thing when doing an oil change.
Justin B.
Reviewed in the United States on August 20, 2024
I'm satisfied with this product, it shipped very quickly in a package covered in Chinese, which had me a little worried quality-wise, but it's exceeded my expectations. The access doors are very handy, I did an oil change with the guard on even.The only thing, which others have stated, is that I had to drill an extra hole on the rear side of the guard to screw in all the necessary bolts. I didn't use the included hardware, I instead bought a small pack of bolts and clips.Other than that, it was relatively easy to install, and for the price, it's a very solid replacement to the OEM cloth-like cover.
Customer
Reviewed in the United States on May 5, 2024
Same shape, perfect hole alignment. Only thing I had to do was drill out 3 more holes for all support screws. Even came with new screws and washers plus bolts and nut clamps. It’s a hard plastic so no sag like the stock felt one. 3 access doors for easy service to. Highly recommend for the focus ST/RS owners.
Arthur S. Brown
Reviewed in the United States on February 12, 2024
**This review is based on INITIAL installation**. Purchased this lower "engine guard/ splash guard" as a replacement on a 2013 Ford Focus ST. Original OEM part was torn, and would not hold its shape anymore and started to drag under the car. This replacement differs from the OEM in a few ways: The OEM unit is some sort of compressed and formed fiber panel, which allows for some flexing, sound dampening, and fluid absorption. This replacement is very sturdy plastic panel, approximately 4 mm thk. The panel ends up being slightly heavier than the original part, and maybe won't dampen road noise as well and any leaks will not get trapped in the panel. This replacement also has well executed (and labeled) access panels that seem to correctly line up for oil filter and oil drain access. These access panels are attached with metal fasteners (flat allen bolts and insert nuts). With the access panels, and being designed compatible for several vehicles, the styling of this panel differs from the original on the Focus ST. But, the overall fitment was very good: it lined up to all the original mounting locations without requiring any modification. Only difference in attachment was that the original panel for the Focus ST had 3 mounting points at the rear edge of the guard, this replacement is only designed using the outer two points on the rear. This was not a surprise and is indicated in the product images. Mounting hardware was provided with the guard, but it was notably larger ( length, diameter) than the original. I currently have it installed reusing the original screws. My initial impressions are really good, and I would not hesitate ordering this again. I will update this review if needed after its been on the car.
Matthew Brown
Reviewed in the United States on November 20, 2024
Cheaply made but it works
Fight Fair
Reviewed in the United States on November 14, 2024
Fits very nicely, used the provided screws and the pan snugged up tightly, the screws are slightly larger than stock but pull everything tougher nice and tight no issues. Love it, way better than stock.
John
Reviewed in the United States on November 23, 2023
The cover lined up perfectly , I had to use different screws but other then that it was perfect. Thank you John
Recommended Products
$69.99
$ 28 .99 $28.99
$14.99
$ 6 .99 $6.99
$113.95
$ 50 .99 $50.99