Your cart is empty.
Your cart is empty.Product Description
John
Reviewed in the United States on February 27, 2025
I used to fiddle around with the glass plate and a glue stick, all that bs until I found this product. Very nice surface texture, no adhesive needed... Won't be going back to anything else
Customer
Reviewed in the United States on February 2, 2025
Amazing product. It makes it so much easier to remove prints from my Ender 3. I had to almost chisel prints from the glass, with this you just peel the sheet off the magnet and flex it a bit. The print pops off.
SAMellor
Reviewed in the United States on January 18, 2025
Was not bad at all to install. Just install to a cold plate. Make sure to level the bed after, as it does raise it up.Printing my first print on it right now. Seems to be going just fine.Magnet is stong, I have no concern that the plate is going to move off of it. No bubbles in my magnetetic part. I start to peel one side of the tape, positioned it, then pull the tape as I set down the magnet. No problems.Easy upgrade to install, and get rif of those clips that the factory build plate uses.
Spacemanfpv
Reviewed in the United States on January 10, 2025
It is sooooo nice, it just adheres to the part, then the part pops off at the end, and no glue needed!
P. Perry
Reviewed in the United States on September 18, 2024
This board changed everything! A tad bit of hairspray for safe measure and your prints sticks super well and this is easiest way I've ever had to remove my prints. Love it!! And it's not even getting scratches from occasional stick, but I didn't put on hot plate. I attached to older glass. The sticky part is a very very hard thing to remove. Would have to remove plate and blow torch it to get it off...imo. But I just set temp 3to4 degrees hotter using glass and magnet plate, adjust Z axis a tad and alls well...
Rubén Aguilera
Reviewed in Mexico on August 17, 2024
Es muy cómoda para retirar las impresiones, Su adhesión es de otro mundo aún sin laca, sólo hay que presionar un poco la punta para que se peque bien, la ventaja es que luego de que queda la impresión, por muy pegada que esté, se levanta fácil.
Héctor FC
Reviewed in Mexico on May 10, 2024
La compré con pocas expectativas ya quecambié a un extrusor con sensor de proximidad sin saber que era necesario tener una cama PEI debido a este sensor, peroestoy muy impresionado con los resultados, mejoró bastante la adhesión de la primera capa, he probado con PLA Y PETG, es super facil remover las piezas y el sensor de proximidad se calibra sin problema con esta cama.
Cadowien
Reviewed in the United States on February 9, 2024
After experiencing adhesion issues with a glass plate, I decided to switch to this bed leveling system paired with a different plate. The difference has been remarkable. Not only are my prints now of higher quality, but they are also far easier to remove compared to when I was using the glass bed. This switch has greatly improved my printing experience, providing both better results and increased convenience.
クロロ
Reviewed in Japan on February 1, 2024
The media could not be loaded.
admd
Reviewed in Canada on December 22, 2024
I purchased this plate under the impression that its dimensions were 265mm x 250mm but it actually measures 235mm x 235mm. The actual size is buried deep within the product description, making the item title misleading. The size mentioned in the title should be removed.
A. H.
Reviewed in the United States on December 21, 2024
This is my second one so far and I can't recommend it enough. No need for glue, just get the leveling right and you are set. Once the plate cools off, prints automatically unstick as if you just set them there. No more scrapers, no more glue, truly a quality of life upgrade.
dfunk
Reviewed in the United States on November 12, 2024
Best build plate I've used!Pros:I have an ender 3 and have had the original bed plate since 2021. I've tried glass plates (hit or miss) but ultimately went back to the original creality bed plate.I use Hatchbox pla and it adheres with zero issues. When printing has finished, my prints come off with ease and no residue. So easy to clean the purge filament and print that I no longer have a use for the scraper that came with the printer.The magnet that you stick to the bed has the precise amount of magnetism you want where it the pei plate won't move during a print but not overly strong where you can remove it. As close to perfect as it gets.The price was absolutely worth it and didn't break the bank at just 15.Quite possibly the best 15 you will spend on an upgrade.Cons: only one con (possibly) if you for whatever reason need access to the screws that hold the adjustment wheels removed it could be difficult since the magnet is stickered onto the bed.Other notes: the size is accurate for my ender 3 and completely disregard the reviewer video that showed his not staying in place. That video was either fake or he did something wrong. I fully recommend this to anyone needing to resolve adhesion issues, or wanting to eliminate clips.I would recommend one more thing before this upgrade: upgrade your knobs to metal and replace your springs with silicone not another set of metal springs. Silicone is superior in my opinion.Hope this helps someone!
レグホーン
Reviewed in Japan on January 23, 2024
ENDER3標準のガラスベッドに糊を使用してきましたが、早く交換すれば良かったと思いました。テストでABSを出漁してみましたが、定着良好、剥がしやすいです。難点を上げるとすれば定着面の凸凹が目立つ程度でラフト設定すれば問題なさそうです。
Recommended Products