Shopping Cart

Your cart is empty.

Your cart is empty.

6.0 Powerstroke Cold Air Intake Kit，4″Cold Air Intake Pipe Kit with Oiled Filter Compatible with 2003-2007 Ford F250 F350 F450 Excursion 6.0L Powerstroke Diesel(Black)

4.8 (8) Write Review
Free shipping on orders over $29.99

$78.59

$ 37 .99 $37.99

In Stock

About this item

  • 【Compatibility】Compatible with 2003-2007 Ford F250/F350/F450/F550 Super Duty 6.0L V8 Diesel（except 2006 Ford F-250 Super Duty Lariat Crew Cab Pickup 4-Door 6.0L)
  • 【Function】Designed to increasing 5-10% horsepower & 6-8% torque, improve your fuel efficiency and creating an attractive intake noise
  • 【Install And Use】 Does not Require Removal of Turbo, Intake Manifold or Up Pipe. Easy to fit with simple tools. No additional parts will be needed for installation after you purchase this kit.
  • 【Package Include】4" mandrel bent Tube NPT fitting for attaching boost gauge Flared 4 inch clamp end and clamped filter end Conical filter with hose clamp Access port and cover plate with screws and o-rings 4" silicone coupler with hose clamps Silicone hose Installation bracket.
  • 【Note】 Our intake kit does not include sensors. Please confirm before purchase.


Product Description

1
2
3

Kerry Cochran
Reviewed in the United States on March 9, 2025
2003 f250, 6.0. The powder coating is good quality, however keep it wrapped during installs. MAF sensor fit was good along with the pcv valve (you may need to modify the pcv hose length. This replaced a high end unit and it sounds better intake the air and a slight performance increase. Take your time installing it and ditch the clamps they give you for the connection at the turbo. Overall it is a good addition.
Customer
Reviewed in the United States on February 20, 2025
Works perfect but instructions would have been nice. Thank goodness for You Tube
Jeff
Reviewed in the United States on January 24, 2025
I had to cut some pieces off to make this fit properly in my 2004 6.0 power stroke. Also seems to let dust in to the turbo because the filter it comes with isn’t that good. But it sure is pretty.
Ryan G
Reviewed in the United States on July 1, 2024
I like this kit, but it had no instructions to install or remove the old OEM unit. I am not a professional mechanic but have wrenched on cars for 40 years, so it was not difficult to install but if you have no real skills, you may be a bit of a challenge. I believe removing to OEM was more difficult than the installation. The blowback hose does have to be modified to fit and an oil catch can will help if so inclined.
Theodore M. Klopf
Reviewed in the United States on May 19, 2024
Pretty much the same product as the sinister cold air intake for a fraction of the cost. It was a perfect fit for my 2003 f250 with the exception of the mounting bracket being a little too long and needing to be shaved back so the mass air flow sensor could be properly seated. Not a big deal if you have an angle grinder on hand. The modification took me all of two minutes. Other than that everything was a perfect fit and it performs very well.
Kenny arbogast
Reviewed in the United States on November 11, 2024
Maf hole is too small. Had to dremel out the opening to get the sensor in.
Conner
Reviewed in the United States on October 6, 2024
Bracket was welded in a spot where the end of it went in front of where the maf sensor belongs & doesn't fit the vehicle it says it'll fit.
John C
Reviewed in the United States on October 29, 2024
Very inexpensive upgrade. I did have to drill a 3/4” hole in the bottom to add the 3/4” vent hose from the valve cover. Other than that smooth install.