Your cart is empty.
Your cart is empty.Product Description
PRODUCT PARAMETERS
- Parameter: Ui 660V, Ith 40A
- Action Type: Manual, Latching Type
- 3 Positions 1-0-2 = ON-OFF-ON, 3 Poles,12 Terminals
- Total Size: 2.50 In. x 2.50 In. x 4.2 In. (LxWxH)
OPTIONAL SPECIAL WIRING
- When switching between 2 input sources for a single output as Change-over switch, Please create a set of jumpers for output to serve as a common Terminal by manual .
- When switching between one input sources for 2 output as Change-over switch, Please create a set of jumpers for input to serve as a common Terminal by manual .
- Automatic Control
- Machine Tool
- Solar Panel System
- Generator
- Inverter, RV and Etc.
Customer
Reviewed in the United States on August 18, 2024
Resesrched a little cause no instructions. But can be used a variety of ways. Using as manual switch from solar to gen.
Lance Theby
Reviewed in the United States on December 31, 2024
bought this so that I could swap from shore power to batter power with out having the danger of both sources being connected at the exact same time. simple. easy to install. works
JNL
Reviewed in Canada on November 12, 2024
The real industrial switch of this type are expensive, having a low-cost alternative for DIY is a great option. This is a typical changeover switch. The wiring is typical, and all the details are in the supplied instructions. The 40A has a larger size than the 20A model, but quite nice.The installation is made by mounting the switch through a hole on a panel, with relevant holes for screws. The switch is not meant to be standalone, it needs to be in an enclosure. In my project I already need a power supply, solid-state relay, so it is a good match. If you only need a switch, then you may find a similar one with an enclosure.There are no certifications valid For Canadian Electrical Code, so this is good for hobby projects, but would not be legal for high voltage.
Yannick
Reviewed in Canada on November 12, 2024
This switch is a very good replacement for the reverse switch on a Grizzly G4000 and other clones metal lathe. The faceplate is numbered with 1 0 2 instead of FWD STOP and REV, this is the main difference. You just need to keep your original faceplate when replacing the switch.The build quality is very good. I've not been able to test the switch at 40 amps, since my lathe doesn't use that much.
CDS
Reviewed in the United States on October 27, 2024
You have to put your thinking hat on for these. Lay it all out on paper before wiring up.
Jrlyrnyrdskynyrd
Reviewed in the United States on January 2, 2024
Bought this as a spare for our RV in case we lose our auto-transfer switch fails away from home.
BJH
Reviewed in the United States on July 8, 2023
I got this for my off-grid cabin. I needed something to let me switch from generator power over to my solar/inverter power without having to unplug extension cords. This is perfect. I have #1 for Generator, #0 for All Off, and #2 for my LiFePo4 Battery/Solar/Inverter system. In the heat of the summer, I have to run the generator to run the window unit air conditioner. But in spring, fall, and winter, I just run lights, fans, TV, radio, water pump, etc, off of the solar system. Most of the lights and fans are 12 volt and do not need the 120 volt power, but the TV, StarLink satellite, power tools do. This was a great price and it quality built. I would definitely recommend this, if you need a changeover switch.
Kenzi falk
Reviewed in the United States on July 7, 2023
I got this switch to make my 3 phase lathe motor reversible. It took me a while to figure out the wiring chart and determine how to wire the switch to do the job. The wiring chart that comes with the switch shows the function diagram but doesn't include a wiring diagram for connecting the switch to a motor. A better diagram would be helpful. The switch is heavy duty with big thick contacts and should last a long time. The crimp on connection clips that are supplied are thick and should carry the required amperage well. The switch will mount on a panel or in a box after you drill a mounting hole. The contact terminal screws have good threads and screwdriver slots. Overall a very good switch for reversing a 3 phase motor. I would get it again.
Chris Shaw
Reviewed in the United States on October 26, 2023
I'm very pleased with the quality and design of this switch. It works well as power source selector switch, although I had to verify which terminals are connected for each selector position. The documentation provided was minimal, but it suits my needs perfectly.
Recommended Products
$12.19
$ 6 .99 $6.99
$19.88
$ 8 .99 $8.99