Your cart is empty.
Your cart is empty.Product Description
Describe
Features
- Dimensions: Stainless Steel Heat Plate 15.875 x 6 inch;Stainless Steel Burner 15.8125 x 1.25 inch. Make sure you measure the size and check the shape of your original parts and compare with ours BEFORE you order
- Fits For Broil King 1992 & later models 9211-64, 9211-67, 9215-54, 9215-57, 9215-64, 9215-67, 9221-54, 9221-57, 9221-64, 9221-67, 9225-64, 9225-67, 9235-24, 9235-27, 9235-84, 9235-87, 9615-54, 9615-57, 9615-64, 9615-67, 9625-54, 9625-57, 9625-64, 9625-67
- Fits For Broil King 9625-84, 9625-87, 9635-84, 9635-87, Baron 320, Baron 340, Baron 420, Baron 440, Baron 490, Baron 540, Baron 590, Baron 590-S.
Even flame
- Even flame&Fully Burned , smooth inside the pipe, can provide enough heat.Stronger and more resistant to rust and burn-through.
Protect Burner
- Protect the burner from food residue, blocking the orifice,The Heat Plate have the exact holes to hold the heat plates in place, easy to install.
Replacement Kit
- We have already matched the burner, heat shield for you and save your pick time.Easy install to your grill,Perfect fit, work well,made your grill like new again.Make sure you measure the size, check the shape of your original parts, and make a comparison with our parts before place order.
Dan Hagen
Reviewed in the United States on July 14, 2024
Everything went in the grill easy enough however it’s just over one year later and 3 of the four tubes are cracked along the Venturi holes and useless. The original broil king tubes lasted 7 years and I’m very disappointed in the quality of these. Will not be buying again.
Brenda
Reviewed in Canada on June 8, 2024
Parts fit perfectly. Very pleased.
Corros
Reviewed in Germany on June 6, 2024
Die Brenner haben keine Quer-Bohrungen, daher zünden nicht beide Seiten. Die Brenner gehen häufiger aus und die Flamme schlägt hinter den Drehknopf. Aufgrund dieser Problematik kann ich sie nicht weiterempfehlen.
Sandro M.
Reviewed in Canada on February 26, 2024
The holes that are drilled to be located in the crossover tube are way off. This makes it very hard to light. I'm returning them.
R. A. Hensel
Reviewed in the United States on August 15, 2023
the grates fit like a charm, however, the burners didn't fit my grill. My burners were still intact so this didn't matter much.
Sight
Reviewed in the United States on July 18, 2023
The quality is great. If your thinking of replacing the insides of your broil king and reading the reviews to make up your mind I was doing the same... Except I didn't get much from the reviews but I'm hear to tell ya it's worth the $50. Especially knowing the $ it cost to buy the expensive *** grill to begin with... Just buy it and come back and thank me later :)
CWT
Reviewed in the United States on June 27, 2023
This was a repeat purchase after about 2 years.Easy replacement for the burners on my Broil King Baron. Also replaced the flame/gas spreader at the same time. The grill was hard to start as the old flame spreader was corroded to the point of having holes/gaps/blockage that didn't allow the flame/gas to spread properly. The burners had deteriorated to where the holes were burning through to each other so it wasn't a uniform flame distribution. This resolved that issue. Adding new burners, a new flame spreader piece, a new battery in the ignitor and possible new grids and you have renewed the life of your expensive grill. I am only getting about two years out of burners and 4 years out of a flame/gas spreader-ignitor.There were no instructions but install is easy. Use channel locks to loosen/wiggle the old burner tubes. Remove the hitch clip locking pins (new ones not included so save these if possible). Remove the burner tubes. Replace the flame spreader piece or clean it out to improve ignition. Adjust the new burner tube air gaps (screened openings) to the same size of your removed burner air gaps (easy with a Philips screwdriver), reinstall burners with hitch pin clips.These seem like quality parts and fits well but only lasted me about 2 years of frequent use.
Norman Whitney
Reviewed in the United States on June 25, 2023
The original burners in my grill were nine years old and starting to rot away. These replacements fit perfectly and function as designed.
Albert Markovski
Reviewed in the United States on October 20, 2023
Hardest part of replacing these in my grill was getting the cotter pins out of the old rusty ones, these new ones fit perfectly and work just like the OEM ones did. They seem to be super high quality, I’d definitely recommend.
Craig
Reviewed in the United States on June 29, 2022
I have a 3.5 year old Baron 320 model and this burner 4 pack fits perfectly and even leaves me with a spare burner. I installed it about 1 month ago and have cooked on it several times. The OEM burners lasted 3.5 years but probably needed replacement many months earlier as they were in really bad shape. The heat plates also fit perfectly and it's nice to have a spare. Not sure if they will last 3 years like the OEM, but initial impression is very positive.I do wish they would add in the cross-over as that was in really bad shape and I had been unable to use the spark starter recently. Replacing the cross-over requires removing the burners, so might as well make it a package. I was able to find that here on Amazon also, just make sure you get the correct set. Search for: Broil King Crossover Tube 15 5/16" x 1 5/8"
Shane M.
Reviewed in the United States on July 11, 2021
Easy to install fit perfect verdict will be out on quality I’ve only use the grill once since replacement.
The popcorn king
Reviewed in Canada on July 20, 2020
Well priced great quality I will order agin
Recommended Products