Your cart is empty.
Your cart is empty.Product Description
Function
These Body Mounts are resistant to vehicle fluids and road grime, maintain proper body and frame alignment, provide more positive attachment to the frame and help insulate the cab while maintaining superior holding power and cushioning effect
Feature
Constructed of a special polyurethane blend that helps insulate the cab while maintaining superior holding power.Scratch resistant,heat resistant,durable.Bring back the comfort ride of the OEM body mounts and include OE-style replacement steel sleeves and bolts.
Installation Tips
1.The seats and carpet must be removed to access the bolt covers because the access to the carpet is covered by the carpet and the vehicle interior.
2.vehicle body properly before removing mounts. SUPPORT ( : Use a 2”x4” piece of wood 24” long or any other suitable RECOMMENDED size between the jack and body panels to spread the load out so as not to damage body panels). If necessary, support the body in several areas.
3.After removing the bolts, the main body must be lifted from the frame by one angle or another, depending on the mounts to be replaced.
4.The body is fastened to the frame with long bolts. These bolts pass through holes in the floor and rubber pads. The cushions are sandwiched between the floor, the frame and the lower cushion.
Installation Instruction:
1.All POSITONS - Loosen the bolts and remove it from the passenger side body mounts，Then loosen the driver’s side body mount bolts, but do not remove them.
2.POSITION 1 - On the front radiator support bolts, you will need to remove the upper nut on the inside of the radiator support and then you can loosen the lower bolt. A 24” extension with a universal swivel and an 18mm socket works well for this on most trucks. You might need to have someone hold the mounts with large adjustable pliers while you loosen the bolts. On some models, the front bumper must be removed to access the bolts.
3.Using a floor jack, carefully place the jack on the passenger side floorboard support mounts and lift high enough to remove the body mounts. Make sure the cab is securely supported with jack stands before working under the truck or removing anymounts.
4.ALL POSITIONS - Remove and replace the passenger side body mounts one at a time. Take care not to mix up the pieces. The upper and lower mounts are clipped together on the frame and you may have to use a pair of large screwdrivers to pry the mounts off.
5.ALL POSITIONS – Install kit body mounts on kit steel mounts, Assemble the kit components.
6.ALL POSITIONS – When installing the new assemblies onto the frame, make sure they are seated into the frame and centered in the hole.
7.POSITION 1 – Install kit body mount M04060-02 on the top, and kit body mount M04060-01 along with kit washer S10126 on the bottom. Run the bolt in from the bottom and start it but don’t tighten it yet. Start the upper nut on the radiator support but don’t tighten it yet.
8.(POSITIONS 2, 3, & 4 – Working on one position at a time, install kit body mount M04060-02 on the large kit steel top half and kit body mount M04060-01 on the small kit steel bottom half. Start the bolts but do not tighten.)
9.Repeat steps 1 through 10 for the driver’s side.
10.Tighten all bolts in an alternating cross pattern (as with tightening wheel lug nuts) until you can feel the stock metal shells seat together (around 45-55 ft. lbs.). Tighten the top nut on the radiator core support mount last.
11.Reinstall the body cab plugs, and if removed, reinstall the seat, trim, and upholstery.
12.Reinstall the airbag fuse and reconnect the battery.
allow tillmon
Reviewed in the United States on May 23, 2023
Pure JUNK. Do NOT buy. I purchased the cab mount set and was short 1 mount. Also all the bolts that came with it would not fit thru the hardware so had to use stock bolts . Mounts are solid and ride of the truck is horrible. Will be replacing these and straight to the trash. Don't waste your money and time
Recommended Products
$64.09
$ 30 .99 $30.99