Your cart is empty.
Your cart is empty.Product Description
About Us
As the pioneer of DTC precision rifle optics and accessories, we continue to challenge the limits of quality and affordability.
- 15+ Years of Optic Experience
- Dedicated Service Department
- Based in California
Monstrum Picatinny Rail Mount for Remington 700 Rifles - Short Action
Crafted specifically for Remington 700 Short Action Rifles
Compatible with Short Action Remington 700 models only including: 223 Remington | 243 Winchester | 308 Winchester | 6.5 Creedmoor | 7 mm Remington Mag | 7 mm-08 Remington | 257 Weatherby Mag | 270 WSM | 22-250 Remington |300 Remington Ultra Mag | 300 AAC Blackout | 220 Swift
Included: 5- #6 bolts, 4- #8 bolts, 1- torx key. (Most Remingtons will use the smaller #6 bolts)
- Installs into OEM mounting holes
- 0 MOA and 20 MOA options for optimal zeroing
- 15-slots to mount your preferred optic
- All hardware included and installs in seconds
Which MOA mount should you choose?
The 0 MOA mount is completely level and is suitable for zeroing your scope at short to mid range distances.
The 20 MOA mount is angled upward at 20 MOA. The angled plane gives you a higher range of elevation adjustment when zeroing your scope. It is suitable for zeroing your scope at long distances.
MISTY S
Reviewed in the United States on March 7, 2025
Good product but giving 4 stars because the cut-out for the shell extractor doesn’t match perfectly to the rifles shell extractor.
Kevin Leung
Reviewed in the United States on February 7, 2025
Fits perfectly and good quality!
Von Briage
Reviewed in the United States on July 3, 2024
It fits perfectly at a very affordable price.Note they give you both types of screws, 8-40 and 6-48. The slightly thinner screws are 6-48 and the most widely used in older factory Rem 700 or Bergara B-14 actions. 8-40 are commonly used in for example Rem 700 Police, custom actions or Bergara Premier actions. Split them up as soon as you get the package. Either way, the base sits flush and sturdy on the action.
R. Dowd
Reviewed in the United States on July 18, 2024
Superior quality and excellent fit on my Colt CBX TacHunter. Rear mounting screws were a little too long and interfered with the bolt, so I filed off a tiny bit and they fit perfectly. Added some blue Loctite, torqued it down and it is solid! Scope holds perfect zero. Highly recommend Monstrum!
WilliamK
Reviewed in the United States on December 4, 2024
My Bergara used the smaller threaded screws. Aligned well and tightened down.
teka125
Reviewed in the United States on December 23, 2024
fit like a glove on rem 700
gable hockaday
Reviewed in the United States on December 20, 2024
The rail fits and work great. The screws provided with the rail are suspect at best. One broke off in my weapon upon installation. Was using a fat wrench torque wrench and the screw broke half way in to installation. So needless to say spend several days removing the broken not stripped fastener out to replace it. By the way I wasn't using thread fastener either.
RidgeRunner
Reviewed in the United States on October 3, 2023
On my model 700 chambered in .223 Winchester the front screw will bottom out against the barrel where it is threaded into the upper receiver before it seats in the rail recess. I cut about 1/3 of the threads off with a Dremel. I cannot recommend doing what I did. getting the shortened screw started was difficult as the tiny little threads were clearly a bit messed up. Perhaps a screw assortment from Harbor Freight or a few washers stacked in the screw recess or even leaving that screw out would be a better solution. All screws I delt with were T15 drive. The original screws are bugle head and the replacements are flat contact surface.Monstrum: If you read this please advise the preferred resolution.
Recommended Products
$11.99
$ 6 .99 $6.99