Your cart is empty.
Your cart is empty.Product Description
Our exclusive adjustable height design allows for absolute precision placement of your optic based on your rifle setup or preferred cheek weld! The riser can be adjusted incrementally via two locking screws from 0.6 inches up to 1 inch of rise, measured from rail surface to rail surface.
Adjust the height of your optic in increments of 0.03 inches.
Crafted from lightweight 6061 aluminum, the mount weighs in at a mere 4.5 ounces!
At a weight comparable to a set of lightweight rings, it provides the added rigidity and convenience of a one piece mount.
Adjustable Height Riser Mount
Built for use with Picatinny or Weaver base optics, our mounts will give you just the right amount of rise for optimal scope positioning and clearance over your front sights. It accepts all Picatinny or Weaver based scopes, red dots, or optics
How to Adjust Riser Mount Height
Loosen the Locking Screws
Loosen the two locking screws located on the side of the riser mount.
Pull Up on the Rail
Pull up on the rail, which will allow you to adjust the height in increments of 0.03 inch.
Note: It may be easier if you first mount the riser mount on to your rifle.
Tighten the Locking Screws
Hand-tighten the locking screws to around 15 in-lb or 1.25 ft-lb.
Note: We always recommend using blue threadlocker whenever there is threading to prevent loosening of screws.
Done!
Now you can mount your optic, if you have not already.
hawk
Reviewed in the United States on March 20, 2025
500 rounds in on a kel tec sub2k and it still holds zero and the high adjustment screws haven’t come loose. The qd stays night a tight even if you take it on and off. Makes a great option for the sub2k for quick removal to fold the sub2k just hook it to the bottom rail for storage. Also the riser allows you to get up and over the iron sights as well as get a more comfortable shooting position by getting you cheek up off the bolt tube.
4th & 10
Reviewed in the United States on February 15, 2025
Easy to use and adjust. My Sig Romeo 5 pairs up nicely with it.
Steve King
Reviewed in the United States on July 15, 2024
easy to install and the quick release makes it easy to remove if my optic fails, the increased height for my optic makes is so much more comfortable to shoot
grannygates
Reviewed in Canada on July 13, 2024
We needed to bump up the sight an inch to make it more comfortable. This was exactly what we needed. Arrived promptly and exactly as described. Very happy with the product and the seller :)
N. Penney
Reviewed in Canada on March 27, 2024
One screw stripped easily... not impressed
Doug Dileonardo
Reviewed in the United States on November 10, 2024
I was able to connect it to my AR with no problem easy on and off and good quality.
Keoki
Reviewed in the United States on September 22, 2022
First, I wanted to say that this isn't that bad of a riser alternative. I like the idea that you can adjust the height, it has a quick detach, is very well priced, and best of all: my EoTech EXPS 2 will fit onto it. The only thing is that the riser does not hold together well when shooting. I tried zeroing my rifle and after 10 shots it comes loose. Tightened it down but after some more shooting, it becomes loose again. I think this would definitely be better for airsoft but not for anything else.
Brian
Reviewed in the United States on November 17, 2022
Very happy first time customer with Monstrum Tactical and I am very pleased with my purchase! I mounted this adjustable riser mount to my rifle and I could not be any happier! The riser mount is very well made and the quaility of this riser mount is second none! The quick release is a very nice option and is very sturdy when locked down and it will not move or ever come loose. The adjustable riser is also a very nice option to have if I decide to purchase more scopes in the future and need to adjust the height of the riser to meet my needs. Highly satisfied and I will be making more purchases with Monstrum Tactical and I highly recommend them to anyone looking to upgrade any firearm!
Grant L. Martin
Reviewed in the United States on June 14, 2020
I received this in good time and good condition. I do have to address the comments regarding its ability to stay on/tight. To the untrained, adjusting the Quick Disconnect tension might not be readily apparent. It needs to be made with the nut and made in small increments. The tension adjustment is achieved by the nut opposite the latch. It needs to be tightened in increments of 1/8 turn or less. When properly adjusted, the latch will begin to close and then at just the point where it seems like it won't close any more, the latch will suddenly snap closed. You have to work up to this situation slowly. It will be obvious to the user where this occurs - At that point, there will be NO movement in the mount/rail at all. The point of "Creeping up" on the correct tension is that If you go too far, you risk breaking off one of the latch cam ears.Note: The inside lip of the nut that bears on the rail clamp is serrated like a lock washer. Make sure the clamp is completely open before turning the nut after the initial installation has been performed. If there is any pressure on the nut, then turning it will be VERY difficult and you WILL score the face of the rail clamp.1] To start, remove any sight on the mount, loosen latch and then the the nut all the way so you can drop the mount onto the rail.2] Set the latch to its closed position. The mount will still be loose on the rail.3] Using your fingers, compress the latch & mount clamps on the rail until the mount clamps are just gripping the rails. While clamped, tighten the nut finger tight. The mount should now stay on the rails with a little movement. It will still be loose but now secure to the point where it's not falling off.4] Now comes the iteration part: Release the clamp, hold the clamps to the rail and tighten the nut 1/8 turn. Now close the clamp and note that it easily closes. Repeat this "Unlatch-tighten nut-latch" process. As you do so, the tension will get greater and greater until you get to that point where the clamp just barely "Comes over the hill", it snaps closed, and the mount will be securely attached to the rail.Using Blue, non-permanent Loctite (#242) , should keep the tension right where you want it .I hope this helps
R B
Reviewed in the United States on October 27, 2020
I needed a little lift with my EoTech to determine if I really need a higher mount configuration. This is a great price, but I am sure it's manufactured in Asia. The quality is good, but the clamp mount adjustment is super sensitive and difficult to get just right. The only reason I will not get this product is the windage offset is too much for my liking. Yes I can adjust the windage on my optic, but I do not like the small offset physically.
Recommended Products
$17.95
$ 7 .99 $7.99