Your cart is empty.
Your cart is empty.ASSEMBLED IN THE USA – This Quick-Strut assembly is assembled with pride in Paragould, Arkansas from domestic and imported components
D. E. Hollenbeck
Reviewed in the United States on February 22, 2025
This Strut is Passenger side ONLY. Monroe Quick-Strut 272492 is the Driver Side. Small detail this is costing me another week!!! No where is it listed Passenger or Driver side. Please Amazon, give us the information we need to get the right parts
Eric Schmidt
Reviewed in the United States on January 30, 2025
Perfect fit for my 2013 CRV.
B
Reviewed in the United States on July 13, 2024
Second UPDATE about 10000 miles in:I investigated the squeaking. Not the struts! A big-brand shop that did my alignment didn't torque the toe bolt for the rear right trailing arm, found it completely loose and the whole trailing arm was shifting left/right about 15 degrees. So it was clunking and squeaking when turning/suspension cycling.Got that tightened up, another alignment done, and the struts continue to be completely quiet!UPDATE about 9000 miles in:The rears have started creaking when cold out or when cycled hard. Ride is fine still, so it's getting ignored.Replaced all 4 struts with Monroe Quick-Struts on a 2007 CRV with ~160k miles. The rears were sagging pretty badly and noticeably cambered out. Would bounce and rebound over speed bumps with no load, and was like a rollercoaster with 4 people in it when hitting a whoop on the highway.Here's the deal with the installs:The fronts were pretty easy. Mind you, I did all of this on a 2-post lift. The rears sucked. Good luck doing them with a floor jack on jackstands. You'll need to have the lower control arm completely disconnected from the unibody front mount, and even then you'll have to pull down on it past maximum droop to give you enough room to get the bottom of the strut out and angled enough to pull it out. The new struts have to go in the same way, from the center of the vehicle up into the mount tunnels, so you'll be laying underneath the center of the car installing them towards the outside. Make sure you watch a couple tutorial videos before you undertake this.Otherwise they're great so far. Those that are dealing with noises probably didn't settle the struts in before torqueing the bolts. The bottoms don't really matter, but the top mounts do. Once they're installed, put the vehicle on the ground and bounce the suspension a bunch and roll it a little back and forth to get them settled, then torque the top mounts in. Do the fronts like you would lugnuts, and the rear you should do the same for the brace plates inside before you torque down the flange nuts.You WILL need at minimum a front-end alignment after these. Mine went from fine (recently aligned) to very bad toe out. I drove it that way for about 50 miles to further let everything settle, then got it aligned. Camber is great again in the front and especially the rear, and with new Moog swaybar links and bushings it drives like new.
SozenDiesel
Reviewed in the United States on September 6, 2023
Overall these struts are defective and are very bad quality. You may be lucky and get one that works but I bought this one and the opposite side one as well. Both were defective and within a few weeks started making noise and clunking noises. Noise could be heard inside the cabin. It sounded like something was loose. Steering also became rough. Recommend avoiding Monroe quick strut
Deb Wolf
Reviewed in the United States on July 26, 2023
Just installed a full set of these. Every detail of the original struts is duplicated making the installation easy. I found no problems at all. When done the car road like new.
RJs Overland Adventure
Reviewed in the United States on March 20, 2023
These Monroe Quick Struts were super simple to install, shipped quickly, were priced well, and were an impressive difference between the old worn out 2012 HONDA CRV struts. Would definitely buy again!
Abraham
Reviewed in the United States on April 22, 2019
I used these to replaced my wife's 2008 Honda CR-V front suspension. We bought the SUV used and it had a really horrible knocking sound from the front passenger tire. I found it was a bad strut. I found this Monroe assembly and figured it would make my life easier than having to risk injury compressing the spring. This assembly went on without a hitch. I replaced the driver's side as well and the knocking is completely gone. Quality of the product looks great. Only time will tell on how long these replacements last. Overall I would highly recommend them.
E
Reviewed in the United States on August 5, 2017
Recently installed these on a Honda CRV - easy as can be and they feel great after 2,500 miles. Can be installed with hand tools. No need for the spring compressor as they come pre-assembeld. I used air because I have it. The only issue with the instal was the poor design of Honda's sway bar link connections - they are cheap rust prone hex key style- absolutely useless in any area that has snow or salt in the air. I ended up replacing those as well..
Recommended Products
