Your cart is empty.
Your cart is empty. Product Feature:
1 Universal mode, suitable for most motorcycles
2 Can effectively reduce deep noise sound, also reduce noise
3 Fit for installation on the exhaust pipe tail exhaust pipe diameter size of 48mm
4 Adjust the size of the outlet to reduce noise The smaller the outlet size, the smaller the sound
Product Specification:
Type: 48mm
End Dia: 48mm/19"
Inlet Pipe Size: 60x25mm/236"x1"(L*D)
Total Length: 82mm/32"
Fixing Bolt Thread Length: 12mm/047"
Adjustable Bolt Thread Length: 8mm/031"
Distance from 1st hole to 4th hole: 32mm/126"
Distance between each hole: 11mm/043"
xlrider66
Reviewed in the United States on June 1, 2024
Returned them .I knew after seeing them, the thin metal would burn up shortly.
Tom Forsythe
Reviewed in the United States on November 9, 2024
The exhaust baffles were exactly what I expected. With a minor alteration they were perfect!👍
Carl Cleary
Reviewed in the United States on July 12, 2023
Well I installed this product with ease. Tightened the provided bolts to where they were very very snug so they wouldn't come loose. Drove my bike about a mile and one of the bolts came out and the baffle came out. Picked it up and went into work. Got to work and noticed the other had done the same. Sounded great while in but don't think I will buy again due to the fact I now have only one flattened baffle and missing one completely since the bolts backed out. Glad I only spent a little over $10 for the pair. If they work for you then that's good but I will just keep my loud pipes for a while longer.
Aaron Bellinger
Reviewed in the United States on September 1, 2022
They did exactly what I expected them to do. I used them to make an internal baffle for a voodoo slip on on my 2013 GSX-R1000. They brought back some back pressure and did the job. I blew the internal plate at the end of the tube out on the first run after install, but I was planning on removing it anyways. I ended up using rivets and a rivet gun to secure the baffle because I trusted them more than the supplied hardware. Other than that, they do a decent job for the money.
Jessica Crater
Reviewed in the United States on May 30, 2022
BUYER BEWARE! Properly installed & after a couple days I started noticing a ticking sound from my exhaust. Pulled the exhaust off and found this baffle had come apart and was vibrating in my pipe. Do not buy these under any circumstance.
John K
Reviewed in the United States on April 24, 2022
I used these to tame some drone from my Porsche Fabspeed Supercups. I started with these wrapped in fiberglass and wire and they were too good at their job. I removed the fiberglass and it really took the edge off while keeping the aggressive tone and volume I was looking for.I'll remove the center plug next just to see what happens. mBut for now I have a very impressive sound while not having ringing ears after drives.
TaG n BaG em Retro
Reviewed in the United States on July 10, 2021
Yamaha vstar xv250, recently bought, previous owner drilled out oem baffles, got these, my pipes are 2", these are little less which is great due to heat expansion so has room not to get stuck in, uses aluminum tape(kind use in hvac around air ducts) to make a snug fit & turned the screw inside out & just tightened bit, held great & works great. messed w it till got adjusted how I wanted for backpressure & sound. these really work well & did great for my intention & has helped, think cool can adjust however want them anytime way I have them fitted in just w hand, so if your needing baffles I deffenetly reccomend these. now they're nothing fancy but work great!
JC
Reviewed in the United States on November 19, 2021
Materials are VERY thin and cheap. Welds aren’t very good or pretty.With that being said, made my extremely loud exhaust too quiet. Sounded stock again. So I removed the adjustable plate, and drilled a few holes in the large flat area and simply stepped up the holes gradually until I got the right amount of exhaust noise from the pipes. Simple temporary solution that works ok.
Recommended Products
