Shopping Cart

Your cart is empty.

Your cart is empty.

Matek SAM-M10Q GNSS Module,GNSS Ublox SAM-M10Q Supports Concurrent Reception of Four GNSS (GPS, GLONASS, Galileo, and BeiDou) for RC Multirotor FPV Racing Drone …

4.3 (2) Write Review
Free shipping on orders over $29.99

$39.99

$ 19 .99 $19.99

In Stock

About this item

  • SAM-M10Q uses multi-constellation GNSS module powered u-blox SAM-M10Q-00B.
  • The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals.
  • SAM-M10Q supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons.
  • Ublox Super-S (Super-Signal) technology offers great RF sensitivity and can improve the dynamic position accuracy in non-line-of-sight scenarios.
  • The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size.The omnidirectional antenna radiation pattern increases flexibility for device installation.


Product Description

  • SAM-M10Q uses multi-constellation GNSS module powered by ublox SAM-M10Q-00B.
  • The SAM-M10Q features the ublox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. SAM-M10Q supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. ublox Super-S (Super-Signal) technology offers great RF sensitivity and can improve the dynamic position accuracy in non-line-of-sight scenarios.
  • The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation.
  • More details about the SAM-M10Q, pls check out ublox SAM-M10Q page.

  • Specifications:
  • GNSS ublox SAM-M10Q-00B (GPS, GLONASS, Galileo and BeiDou)
  • No Magnetic Compass built-in
  • Patch antenna 15*15*4mm
  • Input voltage range: 4~9V (5V pad/pin)
  • Power consumption: 10mA
  • UART baudrate: 9600 default
  • Operating Temperatures: -20~80 °C
  • UART(TX, RX) interface for GNSS SAM-M10Q-00B
  • JST-GH-4P connector (SM04B-GHS-TB). 1.27mm pitch
  • GNSS PPS LED, Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix)
  • Protocol: UBX 5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz
  • 26mm*16mm*8mm
  • 7.5g
  • SAM-M10Q_step.zip

  • Wiring and settings:
  • SAM-M10Q 5V to Flight controller 4~9V
  • SAM-M10Q RX to Flight controller UART_TX
  • SAM-M10Q TX to Flight controller UART_RX
  • SAM-M10Q G to Flight controller GND

  • Tips and Notes:
  • INAV 5.0.0, Betaflight 4.3.0, ArduPilot 4.3 or newer is required.
  • UBlox NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in. once GNSS is powered off and the supercapacitor run out. the settings will back to default.
  • UBloX protocol is bidirectional. Flight controller firmware can change settings on GPS via UBLOX protocol. You don’t need to set GNSS module Baud and Frequency in u-center.
  • The default configuration on SAM-M10Q-00B with ublox FW 5.1 is concurrent reception of GPS, Galileo, GLONASS, and BeiDou B1C with QZSS and SBAS enabled.
  • Start with ublox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed.
  • The SAM-M10Q provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset.
  • The scratches on ceramic antenna are the result of tuning the antenna.
  • u-center Windows

  • Includes:
  • 1x SAM-M10Q
  • 1x JST-GH-4P to JST-GH-4P 20cm silicon wire

Paul
Reviewed in the United States on January 30, 2025
Took a while to get 3D GPS lock, and doesn’t include a magnetometer. Returned and bought a module with integrated magnetometer for half the price that gets GPS lock in a fraction of the time.
Chris Harmon
Reviewed in the United States on October 2, 2023
When I first got back into flying drones it was because DJI had released an HD FPV goggle that would work on smaller drones so I bought a Crux35. Having plenty of experience flying helicotpers and drones line of sight, the first thing I did was fly it straight up a few hundred feet above my house and hover while I looked around the neighborhood that we recently moved to, and about a minute later I looked down and didn't recognize where I was and the picture was getting choppy, I dropped the throttle and dove down hoping to get picture back but it was gone, drone was gone for good. These days I make sure to setup return to home and use a good GPS module and the best I have found for 3.5" and bigger are the MATEKs. I have never experienced any interference from Walksnail or DJI VTX's like I have with Flywoo. If you are experiencing any issues with signal and the usual line shielding doesn't work, I highly recommend trying a Matek.