Your cart is empty.
Your cart is empty.Bolt pattern: 5 on 4.5"; 1/2"-20 studs installed; bearing races installed; Kit also included: 4x L44649 outer cone bearings; 2 x Grease seals; 2 x E Z lube grease caps with rubber plugs; 10 cone wheel nuts 1/2"-20 thread ; Works on most 3500 lbs axles in the market; This hub has been wholesaling by large volume to trailer axle manufacturers
Sean VanDuzen
Reviewed in Canada on March 16, 2024
Easy to assemble and install. Great price!
Race44287
Reviewed in the United States on February 16, 2024
Decent price and fit. Wipe out the inside before installing. There was lots of black casting dust inside them.
John HUTCHINSON
Reviewed in the United States on April 20, 2024
Awesome product good packaging I needed to measure the trailer shaft twice, which was my fault,, quality product and will definitely purchase again (kudos to you) !!!
angela r charles
Reviewed in the United States on June 13, 2023
Kit only had 7 lug nuts in it. Supposed to have 10. Also, the description did not give ID of grease seals. Everything in the kit fits my axle except the grease seals. Had to purchase them separately.
Customer
Reviewed in the United States on March 18, 2023
Shipping was prompt. Box was undamaged. But the VERY thin coat of paint got knocked off in places during shipping. I installed on a boat trailer so the first task was masking and painting. Otherwise it would start rusting immediately. So be ready to paint.Upon installation I discovered that the spacing between the bearing races is less than the shoulders on my spindle. It’s an old trailer so standards may have changed. I had to chase down some 1-1/8 washers to be able to get the bearings tight enough. Without them, there was about a 1/16” of play with the castle nut completely tight. Too much in my book.I bought new bearing buddies made by Reese. They absolutely would not go on. My old covers would. I don’t know if this is a Reese problem or if these hubs ar a bit small.The threads on the studs rough. I chased them a few times with lug nuts and got them working OK.Bottom line - be ready to solve some issuesUpdate - one of the cheap bearings failed after very few miles. Worst, the hubs are made without any relief behind the races. So it’s impossible to drive out the races to replace them.Poor product. AVOID.
Julia Cunningham
Reviewed in the United States on February 27, 2023
I bought this kit to replace the old, worn out, hubs and bearings on my dual jet ski trailer in preparation for a move from Washington State to Central Florida. Like other reviewers, I was a bit concerned about the quality level, but decided to go for it. I'm glad I did. After installing this hub/bearing kit, I pulled that trailer 3200 miles across the country with no problems whatsoever. I probably averaged about 75 mph, with short jumps up to 80. We went through some freezing temperatures in the mountains and temps in the 90's as we went further south. These bearings and hubs worked perfectly in all conditions. For full disclosure, I did pack the bearings with that popular Lucas Oil Sticky Red grease, so some shout-outs to them as well.
anthony h.
Reviewed in the United States on December 18, 2023
They were too long for my axles. Apparently, some older trailers used "short" axles. Correct hubs were expensive so I just did what I should have done first and bought just the bearing kits and replaced the bearings. Still less expensive even after sending these back.
Michael
Reviewed in the United States on December 11, 2021
Ordered set that clearly specified 1-1/16” straight spindles but product shipped had two correct bearing cones and two that did not match the cups (too big). Seals were also not right size to fit in the hub bore. Contacted seller and they shipped correct parts immediately. After that, everything worked well and fit perfectly. Make sure your trailer spindle has correct seal diameter. Parts are for 1-3/8” seal ID. Also may need to add a steel washer (hardware store) if the bearing to bearing dimension is shorter than yours. Easy install and don’t forget to pack with grease.
Gator4x6
Reviewed in the United States on December 20, 2018
These hubs didn't quite fit my boat trailer. They were to long and the wheel lugs were too short. I have a machine shop and there was a lot of modification on the hub. I shorten the hub, bore the inner race dia. deeper and counter bored the back of the hub to let the bolts stick out further in order to bolt the rim. Also the seals were the wrong size for my spindle. It would of helped if the seller would have put more information on the description. Overall the hubs fit now and they look great. I was a tool and die maker and the modification was easy for me and I'm happy with them. So, my suggestion is, before you my any hubs, make sure you get all the dimensions before you purchase them, unless you have a machine shop.
Recommended Products
