Your cart is empty.
Your cart is empty. 9" 9x2.25 solid rubber tire suitable for :
√Xiaomi M365/Pro2
√Hiboy S2
√KUGOO M4
√Aovopro ES80
√all 9inch electric scooter
√etc.
Tire & Tube Size: 9 inch 9x2.25-6 | 9x2.25-36-143
Tire Outer Diameter(without air-filled): 217mm/ (8.54")
Tire Inner diameter: 142mm (5.59")
Tire cross-section height：36mm（1.42"）
Tire Sidewidth: 55mm (2.16")
Weight: 0.83kg
Please note: 9x2.25 inch is the size of the tire after it is mounted to the hub, not the actual size of the physical object. The actual tire size will be a little smaller than 9 inches. The above data are manual measurements, and the allowable error is 0.1-0.5cm/0.03-0.19 inch.
Package contents: Include only what is shown in the picture.
E. Gregory
Reviewed in the United States on March 12, 2025
Fit my NIU KQi1 pro front wheel. Install takes moderate adult strength and protective gloves for when you heat the tire to get it flexible enough to get on the rim. On a few short rides so far it seems like a reasonable replacement where you don't have to worry about a flat anymore.
Tiffany Henness
Reviewed in the United States on May 2, 2024
Bought the wrong size
MR CAMPER
Reviewed in the United States on December 26, 2024
These tires fit the Costco phantom A8 scooter perfectly. They are quite difficult to put on. You will need 2 tire irons (which I already had for my dirtbike) and a larger size vice. I had a longer tire iron, which was easier to really torque the tire upward and then I use the shorter tire iron to hold the tire into place. For the vice, you will need two pieces of wood that can press into the tire and the room itself..Step1- the manufacturer asked you to place the tires in hot water for 15 to 20 minutes boiling, this does make a difference and allows it to stretchStep 2- using a device, and maybe two piece pieces of wood try to squeeze one end of the tire onto the rim. This will also allow you to hold the rim into place so you can take the tire irons and start to stretch the tire onto the base of the rim.Step3- as you place part of the tire on the rim, put a screwdriver through the tire and one of the side holes. Try to hold it in place and then rotate the tire in the vice to another area that you can use the tire irons to push the tire onto the rim. I was constantly working with two tire irons moving the tire into place slowly getting 1/8 at a time over the rim then I would hold it in place and rotate it and do the same thing again and inch or later. Be careful one time I have the tire iron facing upward over the rim and then when the tire adjusted it, snapped the tire iron down and hit me in the wrist leaving a giant welt. It’s a lot harder with smaller tires than larger dirtbike tires.Step 4-once half the tire is on the rim. I sprayed some WD-40 around the rim, I avoided this in the beginning because it made things too slippery.Step 5- after you get the whole entire tire on the rim you will notice it’s not correctly seated into the inside of the rim, spray some more WD-40 around both sides of the rim flange, then with a long screwdriver, pick up that part of the tire, and it will slide into place in the flange. Continue to rotate tire doing this every couple inches and then the tire will finally seat into place.After boiling both tires and getting the scooter in the proper position because I could not disconnect the rear electric wire to the rear rim, so I had to place the scooter at an angle while installing the rear tire, was a real pain in the butt, took about 2 hours total.
John S
Reviewed in the United States on November 11, 2024
If you heat this in your microwave it goes on pretty easily. Wear gloves because it will be hot but it was easier than I thought it would be. So great to not worry about flats anymore!!
Recommended Products
