Your cart is empty.
Your cart is empty. 1.New Products with High Quality
2.Replacement for GY6 50cc Stock Torque and Clutch Springs
3.Fits Most of Chinese Made Scooters and ATV. Such as JONWAY, JMSTAR, ROKETA, SUNL, TANK, PEACE, TAOTAO,JCL,Coolsport,Kazuma
Carlos lozada
Reviewed in the United States on February 6, 2025
Good
Jimthedogman
Reviewed in the United States on February 4, 2025
Great product notable performance change
E Duran
Reviewed in the United States on September 3, 2024
Working good 👍
KEIFFY75 GAMES YT
Reviewed in the United States on August 2, 2024
Works Great, made well, Doesn't engage clutch until rpm's reach 1500, therefore staying higher rpm longer, I also added a 100cc Bore Kit to my Scooter a week after installing this, and its a Huge difference.
m.matrix
Reviewed in the United States on July 19, 2024
I know they work great
shivam
Reviewed in India on December 25, 2024
This is not good for Indian two wheeler as this is not fitting correctly don't waste your money No return and refund till date I haven't been calling them for long time
C. Angeles
Reviewed in Mexico on April 13, 2024
No me sirvieron para la moto que queria, pero los ocupe para otra y quedaron excelentes, recomiendo revisen bien las medidas que necesitan, fuera de eso excelente producto
Luc Thibault
Reviewed in Canada on November 26, 2022
Perfect replacement / tuning for a GY6 Benzhou 50cc Scooter. Mind you folks have to realize there is no unique recipe with those Scooter parts, a lot of variables depending on your configuration, weight etc. Keep on swapping springs and variateur Rollers until you find the sweet spot for you.
Thomas
Reviewed in Canada on April 23, 2021
Fast shipping
ᏣᏐᏂ ᏣᎻᏩᏍ
Reviewed in the United States on April 7, 2019
These give better throttle response and uphill speed on 80cc and 100cc.On 50cc the contra spring cuts take off speed keeping 50cc rpm very high not reaching over gear "Belt to open clutch fully".The "clutch springs" give better pulling power from stopping to pulling away on 50cc,80cc and 100cc.When reinstalling the clutch the easiest way to put the belt back on is to squeeze the clutch open using both hands holding open put the belt on the open clutch then reinstall the clutch with the belt already holding the clutch open to fit over variator easily.Install a new belt also check your variator and weights for wear and no binding.I use Wingsmoto Roller Performance 4 Gram Weights 16X13 in all my mopeds and servicing others mopeds.Caution don't go full throttle constantly down hill's.
Chris
Reviewed in the United States on May 17, 2017
Installed on 2012 agility 50cc with bbk used 9 gram weights,lost some performance on hills,put my 6.5 weights back in and performance is back,had to use the original clutch springs did receive with torque spring,this review was for the red torque spring
Big K-B
Reviewed in the United States on October 15, 2017
Product was in good condition and came with everything in picture. I installed a BBK and added 6-1/2 roller weights I then drove the scooter around and wow it was fast with good tack off mid and top range . I wanted better performance yet so I got this 1500rpm spring I installed it test drove it and lost performance upon tack off It would have to Rev up much more before moving all and all top speed was the same lost tack off and mid , plus it was more stress on the motor and drive train the motor temp went up big time from working harder and the clutch belt and roller s got hot also . I can't say anything bad about the spring it's self it just did not Serv my "Little' scooter any Justice perhaps on a bigger mope like a 150cc it would give the correct performance. I don not recommend for a 50cc not eaven with a BBK .
Recommended Products
$24.99
$ 11 .99 $11.99