Your cart is empty.
Your cart is empty.Product Description
Product
49-22-4146 circular saw rip fence guide kit fits for circular saws 6405-6, 6390-20, 6390-21, 6394-21, 6460 skateplate circular saw guide and replaces circular saw rip fence 49-22-4150.Before ordering products, please confirm that the model you need to buy is consistent with our model.
Fits models
For circular saws 6405-6, 6390-20, 6390-21, 6394-21, 6460 skateplate circular saw guide and replaces circular saw rip fence 49-22-4150.
Advantage
Saves time when making repeated cuts.The circular saw guide is made of high -strength materials to ensure that it is not easy to deform or damage for a long time.
Easy Installation
The 49-22-4146 Circular Saw rip fence guide design is reasonable, easy to hold and operate, even if it is used for a long time, it will not feel tired.Make controlled cuts.
Function
This rip fence kit for circular saw provides you with extra cutting precision. Holds securely across its width so you can cut straight lines with confidence and save time.
Product Reviews
Reviewed in the United States on February 26, 2025
Milwaukee 20 volt it fits right in nicely but it does angle down forward pointing 3% or ? Doesn't interfere and works great.The Bauer 20 volt it would fit better but the saw isn't rigid & installing it in the plate is tricky because the plates are cheap but onces it is installed it becomes an improvement to the saw.
athensoh
Reviewed in the United States on January 15, 2025
This rip fence guide seems to be well built, with a nice, long slide bracket. Unfortunately, I didn't get a chance to use it as it didn't fit my Ryobi P505 circular saw due to the attachment rod being just a little too thick. The rod is about 11.5mm wide and 3mm thick, while the slot on the saw is 2mm thick.
JW
Reviewed in the United States on January 12, 2025
Works just as it should.
Bugsy
Reviewed in the United States on August 13, 2024
I had to cut down some 1" X 6" X 10' pressure treated boards lengthwise down the middle. This guide worked perfectly with my circular saw and made the cut clean and easy. This saved me having to use my big old table saw in the basement and getting sawdust everywhere. I was able to do the job outside where it didn't matter where the sawdust went. My saw already had the spring loaded thumb nut on it, so I can't speak about the nuts that are provided, but they look fine if I had to use them..
Raven’s Teeth
Reviewed in the United States on June 19, 2024
The old Miles rip guide didn't work with the thicker base plates, so I'm trying this guy out.Works well and is close to the dimensions of the slot on the saw. It actually does come with the three twist knobs in product photos. Only complaint so far is how bent out of square the guide was... but this easily bends back to square.
Kent
Reviewed in the United States on October 1, 2024
Used once and it broke
Jon Arnold
Reviewed in the United States on April 4, 2024
Working great
Sara Andaluz
Reviewed in Canada on August 29, 2023
Muy bien
PR
Reviewed in the United States on November 13, 2023
Bought this to use on my new Ryobi cordless 6-1/2" PSBCS01 saw. Ryobi doesn't carry their listed spare part and the other Ryobi alternative parts have size issues. 0.47 inch wide bar is what you want, confirm the item listing specs.None of the provided screws fit the hole, I found some spare that worked so anticipate that. If you tighten it down hard, there's still a little bit of movement. Tighten real hard keeps it from moving but maybe uneven pressure applied over time. I would look into something like thin polyethylene tap over the top and maybe bottom, durable and should be thin enough to shim that little bit of give. Paint or fill in the numbers first in a bright visible color.Everything looked straight, it's essentially one piece. Finish is ok and no sharp edges, could be nicer but it's a small accessory, no need to be so fancy.
Recommended Products