Shopping Cart

Your cart is empty.

Your cart is empty.

2PCs Beitian BE220 M8N GPS Module Support GPS GLONASS BeiDou for RC Long Range FPV Racing Drone Airplane …

Free shipping on orders over $29.99

$25.99

$ 11 .99 $11.99

In Stock

About this item

  • The BE220 M8N GPS module has a flash memory function to save the configuration, which can help you do not need to reset the data next time you use it.
  • Note: it does not have a compass
  • When it is used on Raspberry Pi, it is not necessary to install the driver, but the software must be installed
  • If the TX LED indicator flashes, it means that the BE220 M8N GPS module is operating normally, and the PPS LED indicator flashes to indicate that the GPS module has found your location
  • If you have any questions, you can contact us at any time


Description User Manual
Dimension : 22mm*20mm*6mm
Weight : 5.3g
Connector : 1.00mm spacing between the 4pins patch seat
Specification
Electrical Characteristics
Chipset : M8030-KT
Receiving Format : GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS
Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1
Channels : 72 Searching Channel
Sensitivityv Tracking : -167dBm
Reacquisition : -160dBm
Cold start : -148dBm
Hot start : -156dBm
Accuracy
Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky)
Speed : 0.1m/sec 95% (SA off)
Timing : 1us synchronized to GPS time
Acquisition Time
Cold Start : 26s
Warm start : 25s
Hot start : 1s
Data and Update Rate
Support Rate : 4800bps to 921600bps,Default 9600bps
Data Level : TTL or RS-232,Default TTL level
Data Protocol : NMEA-0183, Default NMEA-0183
Single GNSS : 1Hz-18Hz
Concurrent GNSS : 1Hz-10Hz,Default 1Hz
Operational Limits
Altitude : 50,000m Max
Speed : 515m/s Max
Acceleration : Less than 4g
Electricityconsumption
VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V
Current : Capture 50mA/5.0V
Operating temp : -40 °C ~ +85°C
Storage Temp : -40°C ~ +105°C
Indicator :
TX LED:blue.The data output, TX LED flashing
PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed
Wiring:
GND,TX output,RX input,VCC(3.0v-5.5v)
Package Included
2 x BE-220 GPS Module
2 x 15cm Cable


Voxtel
Reviewed in the United States on August 4, 2024
There are more updated versions out there that support more up-to-date capabilities and messaging formats. But definitely works. Supports 3.3V and 5V, so you can use with both Arduino and Pi.
Mark H.
Reviewed in the United States on August 30, 2023
would not get a gps fix installed correctly 15 minutes no sats m returning
timo
Reviewed in the United States on May 4, 2023
Pros:- Super fast lock- Tons of sats, high accuracy. Regularly see 26+ sats.- Working hot-starts: always boots up with previous sats still locked.- Pretty small, not too heavy for 5+" size drone builds.Cons:- 5.5g isn't very light. Definitely not for micro builds.- Included cables aren't silicone wires but PVC.
Airborn Cloudbase
Reviewed in the United States on January 19, 2021
Good unit , no problems. Fast sat. links after first initial 3d fix which takes forever and accurate RTH locations within 10-15 feet or so for me so far
Customer
Reviewed in the United States on March 1, 2020
works grate
Recommended Products