Your cart is empty.
Your cart is empty.Product Description
1/4-inches air angle die grinder with rubber sleeve technical specifications and dimensions
Kindly reminder:
Before you use the air angle die grinder, please add 2-3 drops of oil from air quick connector and please allow the tool to run for a few seconds after filling to make sure it works well. (oiler not included in our box)
This tool is intended to be operated as a handheld tool and is air-powered. It requires an air compressor that will provide a clean lubricated air, where the air hose is connected to the tool when the tool is running.
Different angle views for 1/4-inches air angle die grinder with rubber sleeve
1/4-inches air angle die grinder with rubber sleeve full set of accessories
1 pcs collet size 1/4" (6.35mm) already installed in angle air die grinder. in the box include 1 pcs 1/4" NPT American standard quick connector and 2 pcs wrench. and 1 pcs added 1/8"(3.18mm) collet.
1/4-inches air angle die grinder with rubber sleeve side view
Industrial grade 1/4 inch collet, high concentricity, small swing, low vibration, high wear resistance, balanced operation.
1/4-inches air angle die grinder with rubber sleeve rear view
The 90-degree head allows flexibility in many applications, for reaching tight or angled grinding.
1/4-inches air angle die grinder with rubber sleeve rear view
Stepless speed control knob switch, according to different purposes, choose different speed. The platen type starts and stop switch is safer and more reliable.
More views for 1/4-inches air angle die grinder with rubber sleeve
1/4-inches air angle die grinder with rubber sleeve air inlet view
The air inlet has a filter to prevent foreign matter from entering, and the air inlet is also a pneumatic oil filler port.
1/4-inches air angle die grinder with rubber sleeve how to adjust the speed
Under normal circumstances, the factory air die grinder has adjusted the speed in the normal working application mode. If you have special requirements for speed, you can adjust the speed again with a screwdriver.
Collet or grinding head installing for 1/4-inches air angle die grinder with rubber sleeve
show how to install collet or grinding head for 1/4-Inches Angle air die grinder, the wrench is included in the sales package and the grinding head is not included.
Instruction manual for 1/4-inches air angle die grinder with rubber sleeve
- Please check off all tightening parts of the tools to be in good condition before operation.
- Working pressure to be 6.3 kg/cm3 (90PSI) at operation.
- Please refer to Figure 1 for the tool installation. To install a filter and a lubricator/oiler at an air outlet
- Release the air supply when replacing Grinding head.
- Wear protection glasses, eye protector, dust mask and gloves at operation.
- Have a short break in every 30minutes to avoid any possible injury due to tiredness.
- Do not have free rotating at high speed to avoid possible injury to the human body and possible tool damage.
- Do not touch the rotating part of the tool with your hand or your body at operation.
Routine maintenance for 1/4-inches air angle die grinder with rubber sleeve
- Stop your Job when finding any irregular sound or vibration at operation and then check and repair the tool.
- Because you are using clean compressed air at operation. Use an air filter at the air installation to clean the dust out of the compressed air.
- Drop some Oil to the inlet of the tool and then run the tool slowly for a minute and finally start your work...Auto Lubricator/oiler is recommended.
- Any dirt dust inside the motor may result in slow rotation even block running, at this time, try to drop some oil from the inlet, see whether solve the problem or return to the seller for maintenance.
- Do release the water out of the air compressor and air hose after an operation.
- Maintain tools with care. Keep tools clean for better and safe performance, follow instructions for lubricating. Inspect tools cords and air hoses periodically, if damaged, have them repaired by an authorized technician.
Alex Fig
Reviewed in the United States on January 26, 2025
Good quality works strong has good speed for the job.
joe
Reviewed in the United States on January 17, 2025
No more than what I use it for does what a pricier grinder would cost just use air tool oil and it should last a long time.
Customer
Reviewed in the United States on August 31, 2024
Have had this product for a year or so and still works well.
Jason Deshong
Reviewed in the United States on February 2, 2024
After only 3 uses the gear mesh came loose. Once this happens on these cheap things it's never right again. You can try to set the mesh correctly and lock the head back into place but it never stays. The threads strip, then it turns into a paperweight. I even had a Harbor Freight version that lasted longer than this. You get what you pay for. I should have known better. Ended up coughing up a few more bucks and bought an Aircat 90 deg die grinder and called it a day.
Betty Boop
Reviewed in the United Kingdom on October 5, 2024
Very happy with item
joachim
Reviewed in Canada on March 22, 2022
de bonne qualité et très satisfait
Serguei E.
Reviewed in Mexico on January 24, 2022
Es un buen maneral y cumple su cometido, tiene un buen agarre gracias a la manga de goma.
Maxime Bouchard
Reviewed in Canada on April 12, 2022
Good
glennayouwanna
Reviewed in the United States on June 9, 2021
Works ok for small sanding discs. As soon as you add a cutoff wheel with a little resistance - terrible - requires a lot more air to keep this thing going well - only tried cutting 20 gauge as well.
Fernando
Reviewed in the United States on March 14, 2021
Great tool, grip keeps your hand from freezing. Would buy again.
M. Rosado
Reviewed in the United States on October 27, 2021
I use 6 different angle grinders. This one is well made, low noise and cost effective.
Jacques
Reviewed in Canada on October 12, 2021
Bonne qualité
Susi Clark
Reviewed in the United States on March 12, 2020
This works great for my husband for work.
Recommended Products